Re: [Serusers] Phone rings but no audio

Hello, I'm running ser 0.8.14 and rtpproxy CVS on debian sarge. You can find my ser.cfg. below. I'm forwarding my calls to a Cisco AS5350 whish serves as a PSTN gateway. I can place a call to a PSTN number and the phne rings, but then no audio is sent or received. I use kphone as a client behind NAT. thnaks Luca --- ser.cfg routing --- route{ # initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if ( msg:len > max_len ) { sl_send_reply("513", "Message too big"); break; }; # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol record_route(); # loose-route processing if (loose_route()) { t_relay(); break; }; # !! Nathelper # Special handling for NATed clients; first,NAT test is # executed: it looks for via!=received and RFC1918 addresses # in Contact (may fail if line-folding is used); also, # the received test should, if completed, should check all # vias for rpesence of received if (nat_uac_test("3")) { # Allow RR-ed requests, as these may indicate that # a NAT-enabled proxy takes care of it; unless it is # a REGISTER if (method == "REGISTER" || ! search("^Record-Route:")) { log("LOG: Someone trying to register from private IP, rewriting\n"); # This will work only for user agents that support symmetric # communication. We tested quite many of them and majority is # smart enough to be symmetric. In some phones it takes a configuration # option. With Cisco 7960, it is called NAT_Enable=Yes, with kphone it is # called "symmetric media" and "symmetric signalling". fix_nated_contact(); # Rewrite contact with source IP of signalling if (method == "INVITE") { fix_nated_sdp("1"); # Add direction=active to SDP }; force_rport(); # Add rport parameter to topmost Via setflag(6); # Mark as NATed }; # we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route(); # subsequent messages withing a dialog should take the # path determined by record-routing if (loose_route()) { # mark routing logic in request append_hf("P-hint: rr-enforced\r\n"); route(1); break; }; if (!uri==myself) { # mark routing logic in request append_hf("P-hint: outbound\r\n"); rewritehostport("$AS5350_IP:5060"); route(1); break; }; # if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) { if (method=="REGISTER") { # Uncomment this if you want to use digest authentication if (!www_authorize("my.domain", "subscriber")) { www_challenge("my.domain", "0"); break; }; save("location"); break; }; lookup("aliases"); if (!uri==myself) { append_hf("P-hint: outbound alias\r\n"); route(1); break; }; # native SIP destinations are handled using our USRLOC DB if (!lookup("location")) { sl_send_reply("404", "Not Found"); break; }; }; append_hf("P-hint: usrloc applied\r\n"); route(1); } # -- nathelper -- route[1] { if (uri=~"[@:](192\.168\.|10\.|172\.(1[6-9]|2[0-9]|3[0-1])\.)" && !search("^Route:")){ sl_send_reply("479", "We don't forward to private IP addresses"); break; }; # if client or server know to be behind a NAT, enable relay if (isflagset(6)) { force_rtp_proxy(); }; # NAT processing of replies; apply to all transactions (for example, # re-INVITEs from public to private UA are hard to identify as # NATed at the moment of request processing); look at replies t_on_reply("1"); # send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if (!t_relay()) { sl_reply_error(); }; } onreply_route[1] { # NATed transaction ? if (isflagset(6) && status =~ "(183)|2[0-9][0-9]") { fix_nated_contact(); force_rtp_proxy(); # otherwise, is it a transaction behind a NAT and we did not # know at time of request processing ? (RFC1918 contacts) } else if (nat_uac_test("1")) { fix_nated_contact(); }; } _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers .