sr-users December 2017

sr-users@lists.kamailio.org

73 participants
100 discussions

Re: [SR-Users] t_drop_replies not working with t_suspend in failure route
by Huber Andreas 03 Sep '21

03 Sep '21

Hi, We’re still using kamailio 4.4 but we’ll be migrating to 5.0 soon. Cool so it will be fixed when we migrate ! Thanks, Andreas From: sr-users [mailto:sr-users-bounces@lists.kamailio.org] On Behalf Of Federico Cabiddu Sent: vendredi 12 mai 2017 11:56 To: Kamailio (SER) - Users Mailing List Subject: Re: [SR-Users] t_drop_replies not working with t_suspend in failure route Hi, which version are you using? A similar case had been reported some months ago and it should be fixed in 5.0. Regards, Federico On Fri, May 12, 2017 at 11:44 AM, Huber Andreas <andreas.huber(a)nagra.com<mailto:andreas.huber@nagra.com>> wrote: Hello, We have a use case where we suspend a transaction in a failure_route to give UEs that might be woken by a push notification more time to REGISTER and join the INVITE. We’d like to drop the previous branches in this case. I tried using t_drop_replies() but it has no effect. The doc states that t_drop_replies() is only working if a new branch is added. And from my understanding t_suspend() adds a new branch. But is it possible that t_drop_replies() cannot be used with t_suspend()? Or am I missing something? Kind Regards, Andreas _______________________________________________ Kamailio (SER) - Users Mailing List sr-users(a)lists.kamailio.org<mailto:sr-users@lists.kamailio.org> https://lists.kamailio.org/cgi-bin/mailman/listinfo/sr-users

2 1

need help with RTPProxy in bridged mode
by Grant Bagdasarian 04 Apr '20

04 Apr '20

Hello, I'm using RTPproxy for the first time in bridged mode and I can't get kamailio/rtpproxy to rewrite the c parameter to the correct public ip address of kamailio. The setup is as following: Carrier ------[fiber]------ Kamailio ---------[lan]--------- Freeswitch Kamailio is listening on two interfaces: 1) Private: 172.0.0.1 2) Public: 192.168.0.1 (since we have a dedicated fiber with our carrier, this is its public address) Freeswitch is listening on: 1) 172.0.0.2 Carrier is on: 1) 10.0.0.1 I've started an rtpproxy instance on the Kamailio box using: rtpproxy -s udp:127.0.0.1:7721 -u rtpproxy rtpproxy -p /var/run/rtpproxy/rtpproxy.pid -l 192.168.0.1 172.0.0.1 I've played around with rtpproxy_manage() and the various flags (ie, ei), but I can't get kamailio to set the correct public IP when the 200 OK has to be sent back to the carrier. It always sets it to its private address, instead of its public address. I'm using Kamailio 4.2 with sippy/rtpproxy 2.0. Could someone please point me into the right direction? Thanks! Grant

4 8

rtpproxy does not response, disable it
by Zodiac 03 Jan '20

03 Jan '20

Dear friends, I am working on a program on Kamailio and rtpengine proxy. I am wondering whether can I set Kamailio and rtpengine daemon on different physical machines. For example, I set Kamailio on a machine with IP address:10.109.247.80, and launch rtpengine daemon on another machine with interface parameter as 10.109.247.90 and ng port 7723. I set parameter in Kamailio.cfg with modparam(“rtpengine”, “rtpengine_sock”, “udp:10.109.247.90:7723”). Unfortunately I got debug message like this: ERROR: rtpengine [rtpengine.c:1710]: send_rtpp_command(): can't send command to a RTP proxy ERROR: rtpengine [rtpengine.c:1746]: send_rtpp_command(): proxy <udp:10.109.247.90:7723> does not respond, disable it ERROR: rtpengine [rtpengine.c:1616]: rtpp_test(): proxy did not respond to ping And, I also tried to set Kamailio and rtpengine daemon in a same machine,and use modparam(“rtpengine”, “rtpengine_sock”, “udp:localhost:7723”). And Kamailio can work functionally under this situation. rtpengine daemon can receive ping message from Kamailio and rtpengine daemon can work as suspected. So for the later case, is it supposed that Kamailio be in the same machine with same localhost address? Otherwise, what’s the reason for my ERROR? ------------------------------------ 北京邮电大学网络技术研究院网络与交换技术国家重点实验室田军 +86 18810315790 mozillafire(a)bupt.edu.cn ------------------------------------

5 10

tcp Free fragment not found
by Diego Nadares 04 Oct '18

04 Oct '18

Hi guys! We have four a scripts that sends dlg.list command to kamailio through xmlrpc. They are not executed simultaneously. Sometimes, we are getting the following errors: fm_search_defrag(): fm_search_defrag(0x7f212c25a000, 5273984); Free fragment not found!2017-05-26T13:54:20.438736-03:00 drwsip02 /usr/local/sbin/kamailio[19833]: ERROR: <core> [mem/f_malloc.c:498]: fm_malloc(): fm_malloc(0x7f212c25a000, 5273984) called from core: tcp_main.c: tcpconn_new(957), module: core; Free fragment not found!2017-05-26T13:54:20.439101-03:00 drwsip02 /usr/local/sbin/kamailio[19833]: ERROR: <core> [tcp_main.c:959]: tcpconn_new(): mem. allocation failure2017-05-26T13:54:20.439344-03:00 drwsip02 /usr/local/sbin/kamailio[19833]: ERROR: <core> [tcp_main.c:3985]: handle_new_connect(): tcpconn_new failed, closing socket I all ready increased this two variables: tcp_conn_wq_max=30000000 tcp_rd_buf_size=5273226 How can I see how much memory xmlrpc is using? Any advice will be appreciated. Thanks in advance! Diego

2 2

Kamctl Stats Update
by Noah Mehl 07 Aug '18

07 Aug '18

Hey all, I was wondering if the kamctl stats output could be updated to provide a bit more parseable JSON? For instance: # kamctl stats shmem | jq . { "jsonrpc": "2.0", "result": [ "shmem:fragments = 18", "shmem:free_size = 467187808", "shmem:max_used_size = 69694104", "shmem:real_used_size = 69683104", "shmem:total_size = 536870912", "shmem:used_size = 41048984" ], "id": 4300 } I would hope would be more like this: { "jsonrpc":"2.0", "result":[ { "shmem":[ { "fragments":18, "free_size":467187808, "max_used_size":69694104, "real_used_size":69683104, "total_size":536870912, "used_size":41048984 } ] } ], "id":4300 } I apologize in advanced because I don’t have the skillset to contribute such a feature. Thanks! ~Noah

5 8

No cdr after Kamailio 5.0.4 and 5.2 dev restart
by Kordován Szabolcs 27 Jul '18

27 Jul '18

Hi All, In March there was a discus about this issue. We tested the new 5.2 dev and 5.0.4 version of Kamailio and we experience that If we restart Kamailio during the call the cdr won't be stored in table acc_cdrs but the data will be inserted to table acc and data will be deleted from table dialog and dialog_vars. Did I omit the fix for it? Thanks for your help. Best regards, Szabolcs

2 3

Kamailio Behind TCP Load Balancer
by Colin Morelli 04 Jun '18

04 Jun '18

Hey all, I'm looking to put Kamailio behind a TCP load balancer that is SIP-unaware. My application is deployed in AWS and I'm tying to place Kamailio behind an ELB. For the most part, everything is fine. For my specific implementation I'm disabling UDP as a signaling transport and using only TLS. This enables me to not have to worry about a SIP-aware LB at the edge because replies to an incoming request will be sent over the existing established TCP socket (avoiding any crazy routing requirements). However - this poses an issue with source addresses. Does Kamailio support anything like the proxy protocol ( http://www.haproxy.org/download/1.5/doc/proxy-protocol.txt) for getting TCP stream information from a load balancer? Do I need to go back to exposing it directly to the world so that I can get source addresses? Thanks, Colin

3 4

Kamailio Websocket Questions
by Nagorny, Dimitry 17 Apr '18

17 Apr '18

Hi List, two questions regarding Kamailio Websockets: 1. How do I send INVITE request TO the listening Websocket? I usually used for UDP/TCP/TLS these format, but somehow this is not working for Websocket because it gets in an endless loop: if ($rU=~"^(\+|00|0)?[1-9][0-9]{4,20}$") { $ru = "sip:" + $rU + "@" + $sel(cfg_get.pstn.gw_ip) + ";user=phone;transport=udp"; force_send_socket(udp:MY_EXTERN_IP:MY_EXTERN_PORT); rtpengine_offer("internal trust-address RTP AVP"); route(RELAY); exit; } 2. Why do I get these errors every time my Websocket Client is registering, but it still works and DB is inserted with registered location: ERROR: <core> [parser/parse_fline.c:257]: parse_first_line(): parse_first_line: bad message (offset: 22) ERROR: <core> [parser/msg_parser.c:690]: parse_msg(): ERROR: parse_msg: message=<HTTP/1.1 101 Switching Protocols#015#012Sia: SIP/2.0/TCP 10.250.5.17:51283#015#012Sec-WebSocket-Protocol: sip#015#012Upgrade: websocket#015#012Connection: upgrade#015#012Sec-WebSocket-Accept: 6uLXlD/aBrzu/j3PYP3DWO7rvLE=#015#012Server: kamailio (4.3.5 (x86_64/linux))#015#012Content-Length: 0#015#012#015#012> I am using Kamailio 4.3.5 + CentOS 7.2. I appreciate every help I can get. Best Regards Dimitry Nagorny Trainee

3 4

Re: [SR-Users] How to determine correct port to set in record-route header
by Pranathi Venkatayogi 30 Mar '18

30 Mar '18

Any help? From: Pranathi Venkatayogi Sent: Monday, January 23, 2017 2:35 PM To: 'Kamailio (SER) - Users Mailing List' <sr-users(a)lists.sip-router.org> Subject: How to determine correct port to set in record-route header Hi, I am using Kamailio behind NAT, unable to figure how to make it put “public ip” in Record-route header, I am manually inserting the hard-coded header myself as below. However now I am having trouble choosing the right port number in all scenarios. $var(dstPort) = 5061; if (dst_port==5060) { $var(dstPort) = 5060; } insert_hf("Record-Route: <sip:MY_PUBLICIP_ADDR:$var(dstPort);transport=tls;lr;nat=yes>\r\n", "Record-Route"); In one scenario I see the conflicting port numbers in “via” header vs “Record route”. The ACK is being set to port 5060 based on Record route header and is not being received by the callee. 2017-01-23 14:52:49.970233 [blink.exe 2780]: SENDING: Packet 11, +0:00:36.411867 10.0.27.108:58217 -(SIP over TLS)-> 172.31.211.31:5061 SIP/2.0 180 Ringing Via: SIP/2.0/TLS 63.149.103.72:5061;received=172.31.211.31;branch=z9hG4bK4799.7067bd2a48063748a4c353fa408eaefa.0 Via: SIP/2.0/UDP 10.0.16.52;rport=5060;branch=z9hG4bK4799.935a27c6ef5ad112225964cbe7c1be44.0;i=2 Via: SIP/2.0/TLS 10.11.200.12:51793;rport=51793;received=10.11.200.12;branch=z9hG4bKPj49f6aeca3f9b4155ab4c5304b544aa4d;alias Record-Route: <sip:63.149.103.72:5060;transport=tls;lr;nat=yes> Record-Route: <sip:10.0.16.52:5061;transport=tls;lr;nat=yes> Call-ID: 09ce10efa6a946bf9445ccc21857393e From: "cust1" <sip:cust1@devtranslation.sms-test.cyracom.com>;tag=95082caabecc42548c2fec5ccd29e5de To: <sip:spanish@translation.sms-test.cyracom.com>;tag=ec365cc8489b48a7bc5725d21b7d97a1 CSeq: 17422 INVITE Server: Blink 3.0.0 (Windows) Contact: <sip:20745891@10.0.27.108:58216;transport=tls> Allow: SUBSCRIBE, NOTIFY, PRACK, INVITE, ACK, BYE, CANCEL, UPDATE, MESSAGE, REFER Content-Length: 0 Questions: 1. How can I let in-built record-route function automatically choose “public ip” so I can get rid of my manual insertion altogether. 2. If no option, what is the right way to choose the port on which packet is being received, so it is same as what is on “VIA”. 3. Any other pointers to improve the logic here?

3 3

authenticating to mongodb fails
by hdssdsdsdsfsdf hdssdsdsdsfsdf 21 Mar '18

21 Mar '18

When I connect using mongo, the credentials work: $ mongo kamailio -u "kam" -p "kam" MongoDB shell version v3.4.9 connecting to: mongodb://127.0.0.1:27017/kamailio MongoDB server version: 3.4.9 > db.subscriber.find() { "_id" : ObjectI ... But when I use the following DBURL in kamailio.cfg, kamailio fails to even login to mongo: #!define DBURL "mongodb://kam:kam@localhost/kamailio" If I disable mongodb authentication, kamailio starts up just fine again. Any idea what's going wrong here?

3 10

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users December 2017