4 May
2007
4 May
'07
10:55 a.m.
Hi,
I have a registered Linksys, behind a USR 9108 modem. I can detect its nat, call Linksys
and speak normally, but when I try to make a call from Linksys, call breaks down right
after call setup. Linksys sends the via and contact ip's as 0.0.0.0 in invite messages
and fix_nated_contact does not work. This is possibly because of the modem but, there are
no extra configurations that can cause this in the modem. I will be glad if you can direct
me with your experiences. thank you...
_________________________________________________________________
Live.com'u deneyin: çevrimiçi dünyanýzý bir araya getirin; haberler, spor, hava durumu
ve çok daha fazlasý.
http://www.live.com/getstarted
4 May
4 May
12:18 p.m.
New subject: [Users] save("location") on reply
Hello users,
i know the subject is ugly but i am dealing with a nasty registrar.
Here is the architecture :
UAC <--> openser <--> registrar (not openser)
Because of various reasons, i HAVE to make openser do save("location")
and this has to be done only when registrar replies a 200 OK.
Here is a piece of my openser.conf :
------------
route{
if (method))"REGISTER") {
t_on_reply("1");
t_relay("udp:registrar")
};
}
route[1] {
save_noreply("location");
}
onreply_route[1] {
if (status=="200") {
route(1);
};
}
------------
My problem is, when a 200 OK arrives, User-Agent and Allow header field
disappeared.
As far as i understood the source code of 'save' function, it reads the
original message (in my case, the received 200 OK packet) before
recording the contact.
This was confirmed when i tried to append_hf("User-Agent: xxx\r\n")
before saving -> it was null in the database.
Do you have any idea how i could get back these fields when receiving a
200 OK?
Best regards,
--
cdt,
Jean-Michel Foucher
OpenWengo, the free and multiplatform VoIP client
http://dev.openwengo.org/
7:33 p.m.
New subject: [Users] save("location") on reply
Hi,
unfortunately I think it is not possible to do what you want. save()
function is specifically ddesigned to work on a SIP request and not on
a SIP reply.
regards,
bogdan
Jean-Michel Foucher wrote:
Hello users,
i know the subject is ugly but i am dealing with a nasty registrar.
Here is the architecture :
UAC <--> openser <--> registrar (not openser)
Because of various reasons, i HAVE to make openser do save("location")
and this has to be done only when registrar replies a 200 OK.
Here is a piece of my openser.conf :
------------
route{
if (method))"REGISTER") {
t_on_reply("1");
t_relay("udp:registrar")
};
}
route[1] {
save_noreply("location");
}
onreply_route[1] {
if (status=="200") {
route(1);
};
}
------------
My problem is, when a 200 OK arrives, User-Agent and Allow header
field disappeared.
As far as i understood the source code of 'save' function, it reads
the original message (in my case, the received 200 OK packet) before
recording the contact.
This was confirmed when i tried to append_hf("User-Agent: xxx\r\n")
before saving -> it was null in the database.
Do you have any idea how i could get back these fields when receiving
a 200 OK?
Best regards,
9 May
9 May
10:23 a.m.
New subject: [Users] save("location") on reply
Bogdan,
unfortunately I think it is not possible to do what you want.
save() function is specifically ddesigned to work on a SIP request
and not on a SIP reply.
all right, thank you for your answer.
I'll try to figure sthg out.
I will post it if it works in case someone is interested.
Regards,
--
cdt,
Jean-Michel Foucher
OpenWengo, the free and multiplatform VoIP client
http://dev.openwengo.org/
25 May
25 May
6:38 p.m.
New subject: [Users] save("location") on reply
Hi Jean-Michel,
It looks like Maxim has committed an enhancement to SER to allow save
of contacts in on_reply route, but I don't think that addresses your
specific issue.
You can check it out here:
http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/registrar/…
http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/registrar/…
Regards,
Ovidiu Sas
On 5/9/07, Jean-Michel Foucher <jean-michel.foucher(a)wengo.com> wrote:
Bogdan,
unfortunately I think it is not possible to do what you want.
save() function is specifically ddesigned to work on a SIP request
and not on a SIP reply.
all right, thank you for your answer.
I'll try to figure sthg out.
I will post it if it works in case someone is interested.
Regards,
--
cdt,
Jean-Michel Foucher
OpenWengo, the free and multiplatform VoIP client
http://dev.openwengo.org/
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users
30 May
30 May
12:44 p.m.
New subject: [Users] save("location") on reply
Hello,
It looks like Maxim has committed an enhancement to
SER to allow save
of contacts in on_reply route, but I don't think that addresses your
specific issue.
no, unfortunately it does not.
Event though save_noreply would be called when a 200 OK is received,
save_noreply should use the original REGISTER in order to gather contact
information.
You can check it out here:
http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/registrar/…
http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/registrar/…
thanks for the links ;)
best regards,
--
cdt,
Jean-Michel Foucher
OpenWengo, the free and multiplatform VoIP client
http://dev.openwengo.org/
1:32 p.m.
New subject: [Users] save("location") on reply
What about copying the contact in the REGISTER into an AVP. Then we
would need a function which stores AVP into location table - e.g.
save($avp(s:contacts));
This function should be useable in request and reply route.
regards
klaus
Jean-Michel Foucher wrote:
Hello,
It looks like Maxim has committed an enhancement
to SER to allow save
of contacts in on_reply route, but I don't think that addresses your
specific issue.
no, unfortunately it does not.
Event though save_noreply would be called when a 200 OK is received,
save_noreply should use the original REGISTER in order to gather contact
information.
thanks for the links ;)
best regards,
1:58 p.m.
New subject: [Users] save("location") on reply
On 05/30/07 14:32, Klaus Darilion wrote:
What about copying the contact in the REGISTER into an
AVP. Then we
would need a function which stores AVP into location table - e.g.
save($avp(s:contacts));
This function should be useable in request and reply route.
there is also the
expires that should be taken in consideration. Also,
in reply, the server can add all the registered contacts, with the
afferent expiration times. What is also important, for nat traversal,
are the received ip and port, source ip and port, which must be taken
from request.
Cheers,
Daniel
regards
klaus
Jean-Michel Foucher wrote:
Hello,
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users
It looks like Maxim has committed an enhancement
to SER to allow save
of contacts in on_reply route, but I don't think that addresses your
specific issue.
no, unfortunately it does not.
Event though save_noreply would be called when a 200 OK is received,
save_noreply should use the original REGISTER in order to gather
contact information.
thanks for the links ;)
best regards,
2:46 p.m.
New subject: [Users] save("location") on reply
Daniel-Constantin Mierla wrote:
On 05/30/07 14:32, Klaus Darilion wrote:
Yes, thats right. My idea was to store all the relevant data into AVP
during request processing and reuse the AVPs when storing in reply route
(only check if response code is 200)
regards
klaus
What about copying the contact in the REGISTER
into an AVP. Then we
would need a function which stores AVP into location table - e.g.
save($avp(s:contacts));
This function should be useable in request and reply route.
there is also the
expires that should be taken in consideration. Also,
in reply, the server can add all the registered contacts, with the
afferent expiration times. What is also important, for nat traversal,
are the received ip and port, source ip and port, which must be taken
from request.
Cheers,
Daniel
>
> regards
> klaus
>
> Jean-Michel Foucher wrote:
>> Hello,
>>> It looks like Maxim has committed an enhancement to SER to allow save
>>> of contacts in on_reply route, but I don't think that addresses your
>>> specific issue.
>> no, unfortunately it does not.
>> Event though save_noreply would be called when a 200 OK is received,
>> save_noreply should use the original REGISTER in order to gather
>> contact information.
>>>
>>> You can check it out here:
>>>
http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/registrar/…
>>>
>>>
http://cvs.berlios.de/cgi-bin/viewcvs.cgi/ser/sip_router/modules/registrar/…
>>>
>> thanks for the links ;)
>>
>> best regards,
>>
>
> _______________________________________________
> Users mailing list
> Users(a)openser.org
> http://openser.org/cgi-bin/mailman/listinfo/users
>
6197
days inactive
6223
days old
8 comments
6 participants
participants (6)
-
Bogdan-Andrei Iancu -
Daniel-Constantin Mierla -
Jean-Michel Foucher -
Klaus Darilion -
Kro Kamil -
Ovidiu Sas