28 Mar
2007
28 Mar
'07
6:28 p.m.
Hi all,
I am having some issues with editing remote party header. I
understand that changes are saved as a diff and are sent when packet
goes on wire. In my current config rpid is edited when invite is
received and it seems to work fine.
There is one scenario where I need to edit rpid or remove rpid
altogether before relaying it. "remove_hf" did not remove the header
after it was edited earlier.
Is there a way to do this?
Thanks in advance for your help.
--
Zahid
30 Mar
30 Mar
3:51 p.m.
Hi Zahid,
try to review the logic on RPID processing to avoid multiple ops on the
hdr. Keep state (use flags, avps, variables), and do only one change at
the end, before relay.
regards,
bogdan
zm23 wrote:
Hi all,
I am having some issues with editing remote party header. I
understand that changes are saved as a diff and are sent when packet
goes on wire. In my current config rpid is edited when invite is
received and it seems to work fine.
There is one scenario where I need to edit rpid or remove rpid
altogether before relaying it. "remove_hf" did not remove the header
after it was edited earlier.
Is there a way to do this?
Thanks in advance for your help.
--Zahid
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users
20 Jun
20 Jun
11:52 p.m.
I have a somewhat similar situation to this. I use remove_hf and
append_hf to modify the RPID in the Request_Route, which works fine, but
then if I try it in Failure_Route I end up with two RPID headers.
Is it possible the revert_uri() is doing something to it? If not, can
you just not do a remove/append like this?
Here are some snippets from my config:
route {
...
...
if (method=="INVITE") {
perl_exec("command", "0"); /*sets rpid and ouri vars*/
if (is_avp_set("$avp(rpid)")){
if(is_present_hf("Remote-Party-ID")){
remove_hf("Remote-Party-ID");
}
append_hf("$avp(rpid)");
}
avp_pushto("$ru","$avp(ouri)");
...
...
failure_route[1]{
if(method == "INVITE" ....blah blah blah
revert_uri();
perl_exec("command", "1"); /*sets rpid and ouri vars*/
if (is_avp_set("$avp(rpid)")){
if(is_present_hf("Remote-Party-ID")){
remove_hf("Remote-Party-ID");
}
append_hf("$avp(rpid)");
}
avp_pushto("$ru","$avp(ouri)");
...
...
Best regards,
Mik Cheez
Bogdan-Andrei Iancu wrote:
Hi Zahid,
try to review the logic on RPID processing to avoid multiple ops on the
hdr. Keep state (use flags, avps, variables), and do only one change at
the end, before relay.
regards,
bogdan
zm23 wrote:
Hi all,
I am having some issues with editing remote party header. I
understand that changes are saved as a diff and are sent when packet
goes on wire. In my current config rpid is edited when invite is
received and it seems to work fine.
There is one scenario where I need to edit rpid or remove rpid
altogether before relaying it. "remove_hf" did not remove the header
after it was edited earlier.
Is there a way to do this?
Thanks in advance for your help.
--Zahid
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users
6154
days inactive
6238
days old
2 comments
3 participants
participants (3)
-
Bogdan-Andrei Iancu -
Mik Cheez -
zm23