4 Feb
2009
4 Feb
'09
8:17 p.m.
I am following the 'mini-Howto on how to configure SER and SEMS to work
together' guide on iptel.org. So I have a separate directory for
integrating the SER and SEMS functionality. For development purposes is
there a switch to change the path were SER looks for the modules? As well
control which version of SEMS is being used? I've installed Sip Express
Media Server (1.1.0-rc1 (i386/linux)) as well as the version from the howto
for testing.
My basic problem is I currently get a version mismatch error:
0(9590) ERROR: module version mismatch for /usr/local/lib/ser/modules/sl.so;
core: ser 0.9.6-sems (i386/linux); module: ser 0.9.6 (i386/linux)
The appropriate modules are located in under my ser-sems test dir and I have
not been successful in redirecting SER to look there.
Also, I have modified ser.cfg and sems.cfg for my system but I did not find
a default ser_sems.cfg. Is this file necessary and where is the default
location?
Thanks for any help or advice.
mll
5 Feb
5 Feb
1:25 p.m.
Hello,
o Martin Lane [02/04/09 20:17]:
I am following the 'mini-Howto on how to configure
SER and SEMS to work
together' guide on iptel.org. So I have a separate directory for
as it says
at the top of that howto, with a more recent version of SEMS
this is not required any more; especially if you are using 1.1.0
version. Also note that there is the 1.1.0 release available
(http://ftp.iptel.org/pub/sems/sems-1.1.0.tar.gz).
For SEMS 1.1.0 (recommended!), you can use the default configuration,
just configure 'application' and the server's IP address and port used
in sems.conf. Then just send the call to the SIP IP:port, e.g. using ser
with t_relay_to_udp("<sip_ip>","<sip_port>");
for completeness, the following comments:
integrating the SER and SEMS functionality. For
development purposes is
there a switch to change the path were SER looks for the modules? As
no, you need
to change every loadmodule line.
well control which version of SEMS is being used?
I've installed Sip
Express Media Server (1.1.0-rc1 (i386/linux)) as well as the version
from the howto for testing.
My basic problem is I currently get a version mismatch error:
0(9590) ERROR: module version mismatch for
/usr/local/lib/ser/modules/sl.so; core: ser 0.9.6-sems (i386/linux);
module: ser 0.9.6 (i386/linux)
Your specific error comes from that the module you are trying to load
was not compiled with the same version, e.g. you have one ser installed
into /usr/local and you have another one in a local directory.
Regards
Stefan
The appropriate modules are located in under my
ser-sems test dir and I
have not been successful in redirecting SER to look there.
Also, I have modified ser.cfg and sems.cfg for my system but I did not
find a default ser_sems.cfg. Is this file necessary and where is the
default location?
Thanks for any help or advice.
mll
------------------------------------------------------------------------
_______________________________________________
Serusers mailing list
Serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
--
Stefan Sayer
VoIP Services
stefan.sayer(a)iptego.com
www.iptego.com
IPTEGO GmbH
Am Borsigturm 40
13507 Berlin
Germany
Amtsgericht Charlottenburg, HRB 101010
Geschaeftsfuehrer: Alexander Hoffmann
5565
days inactive
5566
days old
1 comments
2 participants
participants (2)
-
Martin Lane -
Stefan Sayer