You asked: >> Does the mediatrix be assigned a number too? Can you explain? Normally each port on the Mediatrix is like a UA (like Xten, ... [I might be wrong!!]) That is why, the account you tell it to use should be created in SER first.
NGREP can be found at http://ngrep.sourceforge.net/ After installing it you may use [>>>>>ngrep port 5060] to watch the traffic on port 5060.
When you get the dial tone, what do you do with it? Normally you should be able to dial a number to call. For example if the Xten software is running on your PC and registered to use 500 as main alias, after getting the dial tone (with the phone connected to the Mediatrix) you may dial 500 without hanging up and your UA will start ringing on the PC.
Can you tell me in more details how your devices are interconnected?
Thanks Emery ----- Original Message ----- From: "Sesha B" sesha@iic.com To: "Director General: NEFACOMP" dg@nefacomp.net Sent: Thursday, October 23, 2003 16:58 Subject: RE: [Serusers]SIP Gateway
The analog gateway ID is in readonly mode in my MIB and it is set to 5 by default. I have disabled the redirection and I get the dialtone after two rings. And with the original configuration I have, I get the engage tone after two rings. I have one question! Does the mediatrix be assigned a number too? Also, can you please let me know how do use ngrep to watch the registration headers on the SER registrar? Thank you.
Sesha
-----Original Message----- From: Director General: NEFACOMP [mailto:dg@nefacomp.net] Sent: Thursday, October 23, 2003 10:01 AM To: sesha@iic.com Subject: Re: [Serusers]SIP Gateway
I also have another question about your device: analogGatewayID (.1.3.6.1.4.1.4935.1.1.1.4.1.2.0) = 5
The above line says that your gateway ID is 5. It seems it is different
from
mine. Mine is 2. Possibly I won't be of much help to you. But we can always try.
Can you remove the redirection and see if it works? gatewayPort1RedirectEnable (.1.3.6.1.4.1.4935.1.1.1.4.1.14.10.2.0) = 0 ////// Just disable the redirection to see if that helps gatewayPort1RedirectToAddress (.1.3.6.1.4.1.4935.1.1.1.4.1.14.10.3.0)
=
x.x.x.x gatewayPort1NetToPstnSourceFilter (.1.3.6.1.4.1.4935.1.1.1.4.1.14.10.4.0) = 24.105.144.220
For the remaining parts, I don't see any difference with my configurations (except that you are using country codes while me I have disabled them)
Thanks Emery ----- Original Message ----- From: "Sesha B" sesha@iic.com To: "Director General: NEFACOMP" dg@nefacomp.net Sent: Thursday, October 23, 2003 14:32 Subject: RE: [Serusers]SIP Gateway
I'm attaching my getwalk from the branch voipgateway, which includes everything. The phone I was mentioning earlier is the SIP phone into
which
I'm trying to dial from the regular phones on the PBX. I've the
mediatrix
on
4 ports on the PBX. Thank you.
-----Original Message----- From: Director General: NEFACOMP [mailto:dg@nefacomp.net] Sent: Thursday, October 23, 2003 4:40 AM To: sesha@iic.com; serusers Subject: Re: [Serusers]SIP Gateway
What phone? Can you send me the GetWalk generated by your Unit?
Thanks Emery ----- Original Message ----- From: "Sesha B" sesha@iic.com To: "Director General: NEFACOMP" dg@nefacomp.net; serusers@lists.iptel.org Sent: Thursday, October 23, 2003 00:34 Subject: RE: [Serusers]SIP Gateway
I have these parameters already set. I also restarted mediatrix after setting these MIB variables but I can see only the SIP phone
registering
with the SER in the ser diagnostics but I dont see the SIP gateway's
address
at all !!!
-----Original Message----- From: Director General: NEFACOMP [mailto:dg@nefacomp.net] Sent: Wednesday, October 22, 2003 10:47 AM To: sesha@iic.com; serusers@lists.iptel.org Subject: Re: [Serusers]SIP Gateway
I will send instructions for the first port and you will be able to do
the
same for the other ports.
In the provisioning MIB, find the key: sipMib -> sipUAGroup Start by configuring the SER address: sipMib -> sipUAGroup -> sipUAServerGroup -> sipUAServerStaticGroup and configure the parameters therein. Such as Registrar Host, Port
...
Second, configure the port 1 as follows: sipMib -> sipUAGroup -> sipUA1Group configure the main alias entry which should be the account created
on
the SER server for that port you may even configure other things if needed such as other
aliases,
.... For other ports, just replace # in sipUA#Group by the correct port
number
(2, 3 or 4)
Also, you may need to enable some options in the provisioningMib key.
Thanks Emery ----- Original Message ----- From: "Director General: NEFACOMP" dg@nefacomp.net To: sesha@iic.com; serusers@lists.iptel.org Sent: Wednesday, October 22, 2003 15:53 Subject: Re: [Serusers]SIP Gateway
I was asking the firmware version (the software installed on the
1204).
Not
the Unit Manager.
I am going to send you instructions on how to set up accounts in the
unit.
These are accounts the unit uses in registering with the SER server. Note that you will need to configure the same accounts within SER.
Thanks Emery ----- Original Message ----- From: "Sesha B" sesha@iic.com To: "Director General: NEFACOMP" dg@nefacomp.net;
Sent: Wednesday, October 22, 2003 14:55 Subject: RE: [Serusers]SIP Gateway
Hi, I'm using Unit Manager Express version 1.1.1.5 to configure
Mediatrix
I have configured it to use SIP. I am confused about setting up
accounts
on
Mediatrix. Is there a way to set up accounts on mediatrix? I'm
testing
it
with one SIP phone.
-----Original Message----- From: Director General: NEFACOMP [mailto:dg@nefacomp.net] Sent: Wednesday, October 22, 2003 4:55 AM To: sesha@iic.com; serusers@lists.iptel.org Subject: Re: [Serusers]SIP Gateway
I used Mediatrix 1204. Have set up all the accounts that Mediatrix should use in
registering
to
SER? What software version are your Mediatrix using? You sometimes need
to
upgrade your firmaware. Also, the same Mediatrix can be H.323 or SIP. Are you sure that
yours
is
using SIP?
Thanks Emery ----- Original Message ----- From: "Sesha B" sesha@iic.com To: serusers@lists.iptel.org Sent: Monday, October 20, 2003 23:02 Subject: RE: [Serusers]SIP Gateway
Hi,
I'm using a SIP gateway (Mediatrix 1204) on 4 ports on PBX. I am
not
able
to
register the gateway on the SIP server. Is there a way I check
the
logs
on
the SER to see if it is really registering or not? And can
someone
please
suggest why is the SIP Gateway not registering with the SER?
Thank
you
very
much.
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
-
Director General: NEFACOMP