21 Jun
2014
21 Jun
'14
1:22 p.m.
Hello all!
I make kamailio1 remotely register to kamailio2.
Here I set K1 modparam("uac", "reg_timer_interval", 15), and expires
in uacreg as 30s.
Then K1 should refresh registration after 15s.
However the callid and from tag of every registration are different, and the Cseq just 10
or 11,never increased.In RFC3261, when UAC want refresh bindings, A UA SHOULD use the same
Call-ID for all registrations during a single boot cycle.
Is there any way to reuse the callid and fromtag during refresh registration ? Many
thanks!
And how to make the Cseq become 12 or more?
21 Jun
21 Jun
8:45 p.m.
New subject: UAC module refresh registration, could not reuse callid/fromtag !!!
On 06/21/2014 07:22 AM, nevious wrote:
Hello all!
I make kamailio1 remotely register to kamailio2.
Here I set K1 modparam("uac", "reg_timer_interval", 15), and expires
in
uacreg as 30s.
Then K1 should refresh registration after 15s.
However the callid and from tag of every registration are different, and
the Cseq just 10 or 11,never increased.In RFC3261, when UAC want refresh
bindings, A UA SHOULD use the same Call-ID for all registrations during
a single boot cycle.
Is there any way to reuse the callid and fromtag during refresh
registration ? Many thanks!
And how to make the Cseq become 12 or more?
There is no option to enable your desired behaviour, if that's what you
mean. It would take implementational changes.
--
Alex Balashov - Principal
Evariste Systems LLC
Tel: +1-678-954-0670
Web: http://www.evaristesys.com/, http://www.alexbalashov.com/
Please be kind to the English language:
http://www.entrepreneur.com/article/232906
23 Jun
23 Jun
2:57 p.m.
New subject: UAC module refresh registration, could not reuse callid/fromtag !!!
On 21/06/14 13:22, nevious wrote:
Hello all!
I make kamailio1 remotely register to kamailio2.
Here I set K1 modparam("uac", "reg_timer_interval", 15), and expires
in uacreg as 30s.
Then K1 should refresh registration after 15s.
However the callid and from tag of every registration are different,
and the Cseq just 10 or 11,never increased.In RFC3261, when UAC want
refresh bindings, A UA SHOULD use the same Call-ID for all
registrations during a single boot cycle.
SHOULD is not like MUST, anyhow, can you point the section number inside
the RFC?
Cheers,
Daniel
Is there any way to reuse the callid and fromtag
during refresh
registration ? Many thanks!
And how to make the Cseq become 12 or more?
_______________________________________________
SIP Express Router (SER) and Kamailio (OpenSER) - sr-users mailing list
sr-users(a)lists.sip-router.org
http://lists.sip-router.org/cgi-bin/mailman/listinfo/sr-users
--
Daniel-Constantin Mierla - http://www.asipto.com
http://twitter.com/#!/miconda - http://www.linkedin.com/in/miconda
24 Jun
24 Jun
4:20 a.m.
New subject: UAC module refresh registration, could not reuse callid/fromtag !!!
Thank Godness for your reply!!!
In RFC3261, section 10.2.4 Refreshing Bindings.
I've checked the packages of X-lite and Linphone, they act just like what
the RFC says.
the registration procedure of them like :
R+401+R(auth)+200+R(auth)+200+R(auth)+200+......
During registration, call id and from tag are all the same while Cseq
increased by 1.
Procedure like:
callid[A]/fromtag[B]/Cseq[1]+callid[A]/fromtag[B]/Cseq[2]+callid[A]/fromtag[B]/Cseq[3]+callid[A]/fromtag[B]/Cseq[4]......
I'm sorry I care this so much because if kamailio refresh registration with
different callid and from tag, the remte proxy will consider it a new
registration and delete all dialogs built before.
In ideal circumstances , I'd like kamailio could just re-send the R(auth)
with same Cid an Ftag as a refresh registration before expire.
I'm looking for some breakthrough in source code (too hard!!)
The only clue I've found is tm [callid.c:137] geneate many callid and some
of them are used in register.
tm [callid.c:137]: child_init_callid(): DEBUG:
callid: '5db5df8f-7541(a)127.0.0.1'
And the tm [uac.c:243] prepare to send register request.
tm [uac.c:243]: t_uac_prepare(): DEBUG:tm:t_uac:
next_hop=<sip:10.103.28.190>
So is there any easy way to achieve my goal?
could you give me any directions on source code modification?
I found tm.c tm [uac.c] tm [callid.c] tm[timer.c] may be have sth. to do
with.
Anyway, thank you very very much!! Wish kamailio a good future.
PS: A silly question, is kamailio named from 'KAMA', is a God represent sex
in india.
Just kidding, never mind. :-)
<http://sip-router.1086192.n5.nabble.com/file/n128622/QQ%E5%9B%BE%E7%89%8720140624094608.jpg>
--
View this message in context:
http://sip-router.1086192.n5.nabble.com/UAC-module-refresh-registration-cou…
Sent from the Users mailing list archive at Nabble.com.
30 Jun
30 Jun
3:35 a.m.
New subject: UAC module refresh registration, could not reuse callid/fromtag !!!
I've met a question like this, did you find any ways to reuse the call id and
from tag?
--
View this message in context:
http://sip-router.1086192.n5.nabble.com/UAC-module-refresh-registration-cou…
Sent from the Users mailing list archive at Nabble.com.
3615
days inactive
3624
days old
4 comments
4 participants
participants (4)
-
Alex Balashov -
Daniel-Constantin Mierla -
mailwew -
nevious