Hi,
does anybode know a SIP/SDP field that can be used to set the Bearer Capability to Speech or 3.1 kHz on the outgoing Setup message? We need this for FAX calls because some devices do not accept speech calls.
regards, wolfgang
as a workaround
you can set isdn outgoing-voice info-transfer-capability 3.1kHz-audio on the serial interface
-----Oorspronkelijk bericht----- Van: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org] Namens Wolfgang Platzer Verzonden: maandag 16 februari 2004 8:41 Aan: serusers@lists.iptel.org Onderwerp: [Serusers] Cisco As5300 SIP/ISDN Interworking
Hi,
does anybode know a SIP/SDP field that can be used to set the Bearer Capability to Speech or 3.1 kHz on the outgoing Setup message? We need this for FAX calls because some devices do not accept speech calls.
regards, wolfgang
_______________________________________________ Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
You know that you can set that with the bearer-cap voice-port command? Is that what you were referring to?
Router(config)# voice-port 0:D Router(config-voiceport)# bearer-cap 3100hz
-----Original Message----- From: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org]On Behalf Of Wolfgang Platzer Sent: 16 February 2004 07:41 To: serusers@lists.iptel.org Subject: [Serusers] Cisco As5300 SIP/ISDN Interworking
Hi,
does anybode know a SIP/SDP field that can be used to set the Bearer Capability to Speech or 3.1 kHz on the outgoing Setup message? We need this for FAX calls because some devices do not accept speech calls.
regards, wolfgang
_______________________________________________ Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
------------------------------------------------------------------------------------------------------- This email, and any files transmitted with it, is copyright and may contain confidential information. The contents are intended for the use of the addressee(s) only. Unauthorized use may be unlawful. If you receive this email by mistake, please advise sender immediately. The views of the author may not necessarily constitute the views of Telco Electronics Limited. Nothing in this mail shall bind Telco Electronics Limited in any contract or obligation.
Telco Electronics Limited 6-8 Oxford Court Brackley Northants NN13 7XY
Tel 07000 701999 Fax 07000 701777
Yes I know this possibility. But I don't want to lose one port for Fax calls. I looked for solution where I can set this IE per call basis like in H.323.
regards, wolfgang
You know that you can set that with the bearer-cap voice-port command? Is that what you were referring to?
Router(config)# voice-port 0:D Router(config-voiceport)# bearer-cap 3100hz
-----Original Message----- From: serusers-bounces@iptel.org [mailto:serusers-bounces@lists.iptel.org]On Behalf Of Wolfgang Platzer Sent: 16 February 2004 07:41 To: serusers@lists.iptel.org Subject: [Serusers] Cisco As5300 SIP/ISDN Interworking
Hi,
does anybode know a SIP/SDP field that can be used to set the Bearer Capability to Speech or 3.1 kHz on the outgoing Setup message? We need this for FAX calls because some devices do not accept speech calls.
regards, wolfgang
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers
This email, and any files transmitted with it, is copyright and may contain confidential information. The contents are intended for the use of the addressee(s) only. Unauthorized use may be unlawful. If you receive this email by mistake, please advise sender immediately. The views of the author may not necessarily constitute the views of Telco Electronics Limited. Nothing in this mail shall bind Telco Electronics Limited in any contract or obligation.
Telco Electronics Limited 6-8 Oxford Court Brackley Northants NN13 7XY
Tel 07000 701999 Fax 07000 701777
-
Alan Litster -
David Luyens -
Wolfgang Platzer