19 Mar
2007
19 Mar
'07
11:11 a.m.
Hey guys ,
I noticed that only 1 failure routes is valid for a t_relay .
Is that true or i've done wrong with my config.
What i did was :
If condition A {
t_on_failure("1")
}
If condition B {
T_on_failure("2")
}
t_relay
If it can't be done , how am i suppose to do condition A or B ?
Regards,
Sam
19 Mar
19 Mar
11:15 a.m.
Yup , just found my answer . 1 failure route for 1 t_relay.
So how do i specify my condition ? I can't do it inside the failure
route because some checks cannot be done in there.
________________________________
From: users-bounces(a)openser.org [mailto:users-bounces@openser.org] On
Behalf Of Sam Lee
Sent: Monday, March 19, 2007 4:12 PM
To: users(a)openser.org
Subject: [Users] Failure routes
Hey guys ,
I noticed that only 1 failure routes is valid for a t_relay .
Is that true or i've done wrong with my config.
What i did was :
If condition A {
t_on_failure("1")
}
If condition B {
T_on_failure("2")
}
t_relay
If it can't be done , how am i suppose to do condition A or B ?
Regards,
Sam
11:17 a.m.
Sam Lee wrote:
Hey guys ,
I noticed that only 1 failure routes is valid for a t_relay .
By design you can only activate a single failure route. In your example
you can either:
- make a third failure route which is activated if (A && B) and handle
both situations.
- set flags which are queried in the failure route:
If condition A {
setflag(1)
t_on_failure("1")
}
If condition B {
setflag(2)
T_on_failure("1")
}
failure_route[1] {
if (isflagset(1)) {
....
}
if (isflagset(2)) {
....
}
regards
klaus
Is that true or i've done wrong with my config.
What i did was :
If condition A {
t_on_failure("1")
}
If condition B {
T_on_failure("2")
}
t_relay
If it can't be done , how am i suppose to do condition A or B ?
Regards,
Sam
------------------------------------------------------------------------
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users
--
Klaus Darilion
nic.at
11:18 a.m.
Good one. That should solve my problem.
Thanks for the help Klaus!
Sam
-----Original Message-----
From: Klaus Darilion [mailto:klaus.mailinglists@pernau.at]
Sent: Monday, March 19, 2007 4:17 PM
To: Sam Lee
Cc: users(a)openser.org
Subject: Re: [Users] Failure routes
Sam Lee wrote:
Hey guys ,
I noticed that only 1 failure routes is valid for a t_relay .
By design you can only activate a single failure route. In your example
you can either:
- make a third failure route which is activated if (A && B) and handle
both situations.
- set flags which are queried in the failure route:
If condition A {
setflag(1)
t_on_failure("1")
}
If condition B {
setflag(2)
T_on_failure("1")
}
failure_route[1] {
if (isflagset(1)) {
....
}
if (isflagset(2)) {
....
}
regards
klaus
Is that true or i've done wrong with my config.
What i did was :
If condition A {
t_on_failure("1")
}
If condition B {
T_on_failure("2")
}
t_relay
If it can't be done , how am i suppose to do condition A or B ?
Regards,
Sam
----------------------------------------------------------------------
--
_______________________________________________
Users mailing list
Users(a)openser.org
http://openser.org/cgi-bin/mailman/listinfo/users
--
Klaus Darilion
nic.at
6440
days inactive
6440
days old
3 comments
2 participants
participants (2)
-
Klaus Darilion -
Sam Lee