I have some problem about Cisco and NAT device. I have SER and rtpproxy running on a server. Call is made from a SIP endpoint device to Cisco 5300 gateway via SER. But voice can't hear at my SIP device. I try point to point call without going to Cisco gateway, both side can hear. Please give advise to solve it. Thanks a lot.
The following is my ser.cfg
# # $Id: nathelper.cfg,v 1.1.2.1 2003/11/24 14:47:18 janakj Exp $ # # simple quick-start config script including nathelper support
# This default script includes nathelper support. To make it work # you will also have to install Maxim's RTP proxy. The proxy is enforced # if one of the parties is behind a NAT. # # If you have an endpoing in the public internet which is known to # support symmetric RTP (Cisco PSTN gateway or voicemail, for example), # then you don't have to force RTP proxy. If you don't want to enforce # RTP proxy for some destinations than simply use t_relay() instead of # route(1) # # Sections marked with !! Nathelper contain modifications for nathelper # # NOTE !! This config is EXPERIMENTAL ! # # ----------- global configuration parameters ------------------------
debug= 7 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=no # (cmd line: -E)
# Uncomment these lines to enter debugging mode #fork=no log_stderror=yes
check_via=no # (cmd. line: -v) dns=no # (cmd. line: -r) rev_dns=no # (cmd. line: -R) port=5060 children=4 fifo="/tmp/ser_fifo"
# ------------------ module loading ----------------------------------
# Uncomment this if you want to use SQL database #loadmodule "/usr/local/lib/ser/modules/mysql.so"
loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/textops.so"
# Uncomment this if you want digest authentication # mysql.so must be loaded ! #loadmodule "/usr/local/lib/ser/modules/auth.so" #loadmodule "/usr/local/lib/ser/modules/auth_db.so"
# !! Nathelper loadmodule "/usr/local/lib/ser/modules/nathelper.so"
# ----------------- setting module-specific parameters ---------------
# -- usrloc params --
modparam("usrloc", "db_mode", 0)
# Uncomment this if you want to use SQL database # for persistent storage and comment the previous line #modparam("usrloc", "db_mode", 2)
# -- auth params -- # Uncomment if you are using auth module # #modparam("auth_db", "calculate_ha1", yes) # # If you set "calculate_ha1" parameter to yes (which true in this config), # uncomment also the following parameter) # #modparam("auth_db", "password_column", "password")
# -- rr params -- # add value to ;lr param to make some broken UAs happy modparam("rr", "enable_full_lr", 1)
# !! Nathelper modparam("registrar", "nat_flag", 6) modparam("nathelper", "natping_interval", 30) # Ping interval 30 s modparam("nathelper", "ping_nated_only", 1) # Ping only clients behind NAT
# ------------------------- request routing logic -------------------
# main routing logic
route{
# initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (msg:len >= max_len ) { sl_send_reply("513", "Message too big"); break; };
# !! Nathelper # Special handling for NATed clients; first, NAT test is # executed: it looks for via!=received and RFC1918 addresses # in Contact (may fail if line-folding is used); also, # the received test should, if completed, should check all # vias for rpesence of received if (nat_uac_test("3")) { # Allow RR-ed requests, as these may indicate that # a NAT-enabled proxy takes care of it; unless it is # a REGISTER
if (method == "REGISTER" || ! search("^Record-Route:")) { log("LOG: Someone trying to register from private IP, rewriting\n");
# This will work only for user agents that support symmetric # communication. We tested quite many of them and majority is # smart enough to be symmetric. In some phones it takes a configuration # option. With Cisco 7960, it is called NAT_Enable=Yes, with kphone it is # called "symmetric media" and "symmetric signalling".
fix_nated_contact(); # Rewrite contact with source IP of signalling if (method == "INVITE") { fix_nated_sdp("1"); # Add direction=active to SDP }; force_rport(); # Add rport parameter to topmost Via setflag(6); # Mark as NATed }; };
# we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route();
# subsequent messages withing a dialog should take the # path determined by record-routing if (loose_route()) { # mark routing logic in request log(1, "loose_route processing\n"); append_hf("P-hint: rr-enforced\r\n"); t_relay(); route(1); break; };
if (!uri==myself) { # mark routing logic in request append_hf("P-hint: outbound\r\n"); route(1); break; };
# if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) {
if (method=="REGISTER") { save("location"); break; }; lookup("aliases"); if (!uri==myself) { append_hf("P-hint: outbound alias\r\n"); route(1); break; }; if ( uri=~"^sip:9[0-9]*@5300_IP" ) { log(1, "SER22: matched - forward to GW\n"); fix_nated_sdp("2"); force_rtp_proxy("5300_IP"); rewritehostport ("5300_IP:5060"); t_relay_to_udp("5300_IP","5060"); forward(5300_IP, 5060); break; }; if (!lookup("location")) { sl_send_reply("404", "Not Found"); break; };
};
append_hf("P-hint: usrloc applied\r\n"); route(1); }
route[1] { # !! Nathelper if (uri=~"[@:](192.168.|10.|172.(1[6-9]|2[0-9]|3[0-1]).)" && !search("^Route:")){ sl_send_reply("479", "We don't forward to private IP addresses"); break; }; # if client or server know to be behind a NAT, enable relay if (isflagset(6)) { force_rtp_proxy(); }; # NAT processing of replies; apply to all transactions (for example, # re-INVITEs from public to private UA are hard to identify as # NATed at the moment of request processing); look at replies t_on_reply("1");
# send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if(!t_relay()) { sl_reply_error(); }; }
# !! Nathelper onreply_route[1] { # NATed transaction ? if (isflagset(6) && status =~ "(183)|2[0-9][0-9]") { fix_nated_contact(); force_rtp_proxy(); # otherwise, is it a transaction behind a NAT and we did not # know at time of request processing ? (RFC1918 contacts) } else if (nat_uac_test("1")) { fix_nated_contact(); }; }
_________________________________________________________________ 「碧咸嫂」點樣學外語? http://go.msnserver.com/HK/46164.asp