Kamran, There is not rtpproxy installation. Just start it... It will communicate through the default Unix socket. You need to make sure that rtpproxy has the correct version number to communicate with your ser version. You will find instructions in the Getting Started document at http://onsip.org/ as well as a ser Getting Started source package where the versions match. g-)
Kamran Ahmad wrote:
hello
NATHelper Module is usefull in communicating through sip.
now i am getting calles on both sides of NAT but without voice. here is my "var/log/messages"
need help on RTP Proxy. how to install RTPProxy.
Apr 9 01:55:10 achieva ser[10869]: ERROR: force_rtp_proxy2: support for RTP proxy is disabled Apr 9 01:55:15 achieva ser[10870]: ERROR: send_rtpp_command: can't connect to RTP proxy Apr 9 01:55:15 achieva ser[10870]: WARNING: rtpp_test: can't get version of the RTP proxy Apr 9 01:55:15 achieva ser[10870]: WARNING: rtpp_test: support for RTP proxyhas been disabled temporarily Apr 9 01:55:15 achieva ser[10870]: ERROR: force_rtp_proxy2: support for RTP proxy is disabled Apr 9 01:55:15 achieva ser[10870]: ERROR: on_reply processing failed
ser.cfg
debug=3 # debug level (cmd line: -dddddddddd) fork=yes log_stderror=no # (cmd line: -E)
/* Uncomment these lines to enter debugging mode fork=no log_stderror=yes */
check_via=no # (cmd. line: -v) dns=no # (cmd. line: -r) rev_dns=no # (cmd. line: -R) port=5060 children=4 fifo="/tmp/ser_fifo"
# ------------------ module loading
# Uncomment this if you want to use SQL database #loadmodule "/usr/local/lib/ser/modules/mysql.so"
loadmodule "/usr/local/lib/ser/modules/sl.so" loadmodule "/usr/local/lib/ser/modules/tm.so" loadmodule "/usr/local/lib/ser/modules/rr.so" loadmodule "/usr/local/lib/ser/modules/maxfwd.so" loadmodule "/usr/local/lib/ser/modules/usrloc.so" loadmodule "/usr/local/lib/ser/modules/registrar.so" loadmodule "/usr/local/lib/ser/modules/textops.so"
# Uncomment this if you want digest authentication # mysql.so must be loaded ! #loadmodule "/usr/local/lib/ser/modules/auth.so" #loadmodule "/usr/local/lib/ser/modules/auth_db.so"
# !! Nathelper loadmodule "/usr/local/lib/ser/modules/nathelper.so"
# ----------------- setting module-specific parameters
# -- usrloc params --
modparam("usrloc", "db_mode", 0)
# Uncomment this if you want to use SQL database # for persistent storage and comment the previous line #modparam("usrloc", "db_mode", 2)
# -- auth params -- # Uncomment if you are using auth module # #modparam("auth_db", "calculate_ha1", yes) # # If you set "calculate_ha1" parameter to yes (which true in this config), # uncomment also the following parameter) # #modparam("auth_db", "password_column", "password")
# -- rr params -- # add value to ;lr param to make some broken UAs happy modparam("rr", "enable_full_lr", 1)
# !! Nathelper modparam("registrar", "nat_flag", 6) modparam("nathelper", "natping_interval", 30) # Ping interval 30 s modparam("nathelper", "ping_nated_only", 1) # Ping only clients behind NAT
# ------------------------- request routing logic
# main routing logic
route{
# initial sanity checks -- messages with # max_forwards==0, or excessively long requests if (!mf_process_maxfwd_header("10")) { sl_send_reply("483","Too Many Hops"); break; }; if (msg:len >= max_len ) { sl_send_reply("513", "Message too big"); break; };
# !! Nathelper# Special handling for NATed clients; first, NAT test is # executed: it looks for via!=received and RFC1918 addresses # in Contact (may fail if line-folding is used); also, # the received test should, if completed, should check all # vias for rpesence of received if (nat_uac_test("3")) { # Allow RR-ed requests, as these may indicate that # a NAT-enabled proxy takes care of it; unless it is # a REGISTER
if (method == "REGISTER" || ! search("^Record-Route:")) { log("LOG: Someone trying to register from private IP, rewriting\n");
# This will work only for user agents thatsupport symmetric # communication. We tested quite many of them and majority is # smart enough to be symmetric. In some phones it takes a configuration # option. With Cisco 7960, it is called NAT_Enable=Yes, with kphone it is # called "symmetric media" and "symmetric signalling".
fix_nated_contact(); # Rewrite contact withsource IP of signalling if (method == "INVITE") { fix_nated_sdp("1"); # Add direction=active to SDP }; force_rport(); # Add rport parameter to topmost Via setflag(6); # Mark as NATed }; };
# we record-route all messages -- to make sure that # subsequent messages will go through our proxy; that's # particularly good if upstream and downstream entities # use different transport protocol if (!method=="REGISTER") record_route();
# subsequent messages withing a dialog should take the # path determined by record-routing if (loose_route()) { # mark routing logic in request append_hf("P-hint: rr-enforced\r\n"); route(1); break; };
if (!uri==myself) { # mark routing logic in request append_hf("P-hint: outbound\r\n"); route(1); break; };
# if the request is for other domain use UsrLoc # (in case, it does not work, use the following command # with proper names and addresses in it) if (uri==myself) {
if (method=="REGISTER") {
# Uncomment this if you want to use digest authentication # if (!www_authorize("iptel.org", "subscriber")) { # www_challenge("iptel.org", "0"); # break; # };
save("location"); break; };
lookup("aliases"); if (!uri==myself) { append_hf("P-hint: outbound alias\r\n"); route(1); break; };
# native SIP destinations are handled using our USRLOC DB if (!lookup("location")) { sl_send_reply("404", "Not Found"); break; }; }; append_hf("P-hint: usrloc applied\r\n"); route(1); }
route[1] { # !! Nathelper if (uri=~"[@:](192.168.|10.|172.(1[6-9]|2[0-9]|3[0-1]).)" && !search("^Route:")){ sl_send_reply("479", "We don't forward to private IP addresses"); break; };
# if client or server know to be behind a NAT, enable relay if (isflagset(6)) { force_rtp_proxy(); };
# NAT processing of replies; apply to all transactions (for example, # re-INVITEs from public to private UA are hard to identify as # NATed at the moment of request processing); look at replies t_on_reply("1");
# send it out now; use stateful forwarding as it works reliably # even for UDP2TCP if (!t_relay()) { sl_reply_error(); }; }
# !! Nathelper onreply_route[1] { # NATed transaction ? if (isflagset(6) && status =~ "(183)|2[0-9][0-9]") { fix_nated_contact(); force_rtp_proxy(); # otherwise, is it a transaction behind a NAT and we did not # know at time of request processing ? (RFC1918 contacts) } else if (nat_uac_test("1")) { fix_nated_contact(); }; }
Do you Yahoo!? Yahoo! Small Business - Try our new resources site! http://smallbusiness.yahoo.com/resources/
Serusers mailing list serusers@lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers