sr-users

sr-users@lists.kamailio.org

42 participants
37517 discussions

[Users] New presence server: immediate NOTIFY missing
by Franz Edler 01 Nov '06

01 Nov '06

Hello, many thanks to all developers of the new presence server. Its a great enhancement to OpenSER. As a small contribution from my side I did some tests with Eyebeam clients. Now I found, that the immediate NOTIFY according to RFC3265 § 3.1.6.2 is missing. To document the behaviour I have attached a trace-file from the server. Frame 6 contains a SUBSCRIBE request which is not confirmed with an immediate NOTIFY request. The first NOTIFY is sent only four minutes later after the first presence state change of the presentity occurred (frame 30). Cheers Franz

4 9

[Users] TLS: what is encrypted in TLS?
by Ferianto siregar 01 Nov '06

01 Nov '06

Dear all, Thank you for this chance. All, I have tried to learn about how can TLS can secure communication in VoIP. I must to understand it in order to responsible my openser server (working) with TLS to my lecturer. But, I have still doubt. Actually, what is encrypted in TLS system so the communication become secure? Does it encrypt the data (voise packet)? or The traffic (so the sniffer can not get the data? OR anything else? I do hope anybody can help me :) Thanks, Ferianto Note: I cryptography tutorials, I read that the cryptography system secure the message (text) by encrypting it using public key and private key. So, How about TLS in VoIP? --------------------------------- Everyone is raving about the all-new Yahoo! Mail.

2 1

[Serusers] on hold problem
by Shaun Hofer 01 Nov '06

01 Nov '06

Hi, I've been having a problem, where audio is lost either in one or both directions when conversaion is taken off 'hold'. The parties are both behind NAT and depending UA as whether one or both loose audio. From what I can tell its to do with my loose route and nathelper, and how my ser.cfg deals with the take off hold INVITE from the phones. When the call is taken off hold the rtp streams aren't setup properly again (eg not using mediaproxy correctly). What is the best way to solve this problem? I've seen similarly posts to the mailing list about this problem with no solution posted. http://lists.iptel.org/pipermail/serusers/2006-March/027424.html http://lists.iptel.org/pipermail/serusers/2006-April/027885.html http://lists.iptel.org/pipermail/serusers/2006-May/028407.html Thanks Shaun I have a similarly config to getting started guides ser.cfg # ----------------------------------------------------------------- # Loose Route Section # ----------------------------------------------------------------- if (loose_route()) { if (!has_totag()) { sl_send_reply("403", "Forbidden"); break; }; if (method=="INVITE") { if ((method=="INVITE" || method=="REFER") && !has_totag()) { if (!proxy_authorize("","subscriber")) { proxy_challenge("","0"); break; } else if (!check_from()) { sl_send_reply("403", "Use From=ID"); break; }; consume_credentials(); }; if (client_nat_test("3")||search("^Route:.*;nat=yes")) { setflag(6); use_media_proxy(); }; }; route(1); break; };

3 8

[Users] cpledit
by Doug Meredith 31 Oct '06

31 Oct '06

Hi, I'm trying to find cpledit. It is no longer at iptel.org. Someone on the SER mailing list told me to try here, as he thought Bogdan was behind it. Does anyone know if this still exists and where I can find it? Can anyone suggest an alternative? Thanks for any help. Doug -- Doug Meredith 506-854-7997 ext. 801

2 2

[Serusers] test message
by SER LIST 31 Oct '06

31 Oct '06

pls. ignore _________________________________________________________________ Not only does Windows Live OneCare provide all-in-one PC care to keep your computer protected and well-maintained, but it also makes creating backup files a breeze. Try it today! http://ideas.live.com/programpage.aspx?versionid=b2456790-90e6-4d28-9219-5d…

1 0

[Users] Implementing the CDS(Call Detail Record)
by ShivaSankar Padhy 31 Oct '06

31 Oct '06

Dear All, Can I implement the CDR without using the RADIUS Server.??I am using openser 1.0.1 notls. Expecting a sooner reply, Thanks in Advance, Shiva

2 1

[Serusers] help in mediaproxy module
by vijay tiwari 31 Oct '06

31 Oct '06

hi all i have problem in configurations of mediaproxy module i have download mediaproxy in my ser server and i have make one file name(mediaproxy.ini) in mediaproxy dir and do some change and run this command mediaproxy start nothing can heppand please help me out on this because at this time i am in very bad conditions thanks vijay --------------------------------- Everyone is raving about the all-new Yahoo! Mail.

1 0

[Users] CVS 31.03, TLS and dead tcp child
by Frank DInnocenzo 31 Oct '06

31 Oct '06

Hello, I'm new to openSer and wondered if there was any resolution to this post??? I'm hitting this same crash with openSer (with TLS enabled) using a Snom phone (300 with latest Beta firmware - snom300-6.5-SIP-j.bin). I've gone through the archives looking for help getting this setup working. I've also tried the Snom Softphone with the same result. Thanks Frank >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Hi, I have tried to register to OpenSER CVS 31.03 with my SNOM 360 (5.3.6sw), disabled pretty all modules from OpenSER (radius, xlog, auth, ...) and always the server crashes. Is there something I have missed in configuration ? Thanks a lot for help, -Mika The error message and debug info seems like this: 11(24351) tcpconn_new: new tcp connection to: XXX.XX.XX.XXX 11(24351) tcpconn_new: on port 2171, type 3 11(24351) tls_tcpconn_init: Entered: Creating a whole new ssl connection 11(24351) tls_tcpconn_init: Looking up tls domain [XXX.XX.XX.XXX:5061] 11(24351) tls_tcpconn_init: Using default tls server settings 11(24351) tls_tcpconn_init: Setting in ACCEPT mode (server) 11(24351) tcpconn_add: hashes: 442, 1 11(24351) handle_new_connect: new connection: 0xb608f6a0 24 flags: 0002 11(24351) send2child: to tcp child 0 7(24347), 0xb608f6a0 7(24347) received n=4 con=0xb608f6a0, fd=19 7(24347) DBG: io_watch_add(0x810e580, 19, 2, 0xb608f6a0), fd_no=1 7(24347) tls_update_fd: New fd is 19 11(24351) DBG: handle_tcp_child: dead tcp child 0 (pid 24347, no 7) (shutting down?) 11(24351) DBG: io_watch_del (0x810e420, 17, -1, 0x0) fd_no=16 called 11(24351) ERROR: receive_fd: EOF on 15 11(24351) DBG: handle_ser_child: dead child 7, pid 24347 (shutting down?) 11(24351) DBG: io_watch_del (0x810e420, 15, -1, 0x0) fd_no=15 called 0(24339) child process 24347 exited by a signal 11 0(24339) core was generated 0(24339) INFO: terminating due to SIGCHLD 6(24346) INFO: signal 15 received 6(24346) Memory status (pkg): --------------------------------- Stay in the know. Pulse on the new Yahoo.com. Check it out.

2 3

[Users] Re: openser
by samuel 31 Oct '06

31 Oct '06

First of all: It's not considered polite to send direct mails for topics which ought to be directed to the mailing list... Try to go to www.onsip.org and download the getting started document, which has a good explanation and several examples for configuring. It is targeted to SER but your openser version should be really close to the config files explained in the getting started document...You might have to adapt some syntax so you would have to check the logs when you start openser. Samuel. 2006/10/31, simo med <simoelmar(a)gmail.com>: > hi Samuel! > i'm asking for an example type of an openser.cfg! if you have any > information or a solution to make my openser work properly, please send it > to me! > i use openser 1.0.1, in linux debian! > thanks in advance > simo

1 0

[Serusers] No query limit ?
by inge 31 Oct '06

31 Oct '06

Hi all, I find a way to show all result for accounting page. I don't want to split it in some pages. So I find in "method.get_acc_entries" the parameter. I write false instead of true. Then I see all entries for the query, but there is always the split in some pages. So for each pages I have all result (lol). Someone have an idea ? Regards.

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users