sr-users

sr-users@lists.kamailio.org

4 participants
37456 discussions

[Serusers] Question about Radius Leg
by Gustavo Passos Tourinho 20 Mar '07

20 Mar '07

Hello I saw a Stop-Ack LEG and I would like to know what kind of signaling message could generate it. I mean, that 183 is Session Progress I know but why it generate Stop Ack leg? Shouldnt I have only start-ack (ACK send after 200 OK was received)? This is a quote of my radius log Thu Mar 15 13:49:18 2007 Acct-Status-Type = Stop Service-Type = IAPP-Register Sip-Response-Code = 183 Error-Cause = Ack Thanks, Gustavo

2 1

[Serusers] compiling the most recent unstable snapshots
by Eliott Spencer 20 Mar '07

20 Mar '07

I am having difficulty compiling the most recent unstable snapshots on Debian (Ubuntu Feisty Fawn) starting with the version released March 3rd. Previous versions compile well so I have been using the March 1st release and am learning a lot about the new SER (I really like @selects). My compile gets stuck at the eval module but when I skip that module, it gets stuck at the unixsock module. If I skip that module it gets stuck at another module and so on until when I finish compiling it won't start. Am I missing a key step or command? Thanks!

2 1

[Serusers] Problem loading mysql module
by POON Ben 20 Mar '07

20 Mar '07

Hi, I installed SER 0.9.3 for Solaris 10 (is there a newer version pre-compiled for solaris 10?). I'm using the sample config it comes with, except I uncommented the line: loadmodule "/usr/local/lib/ser/modules/mysql.so" Having done that, I get this error: 0(23162) ERROR: load_module: could not open module </usr/local/lib/ser/modules/mysql.so>: ld.so.1: ser: fatal: libmysqlclient.so.10: open failed: No such file or directory I have installed MySQL already, and I checked that mysql.so is where it should be. Is there something else I have to configure to get MySQL running with SER? Thanks, Ben

4 3

[Serusers] Ser2 and radius - Accounting request doesn't send User-Name Attribute
by tzieleniewski 20 Mar '07

20 Mar '07

Hi, I am using radius for accounting and I have the following problem that whenever SER sends an Accounting message to Radius which contains the Acct-Status-Type = Start it doesn't send the User-Name attribute. Strange is that the User-Name is send with the massage with Acct-Status-Type = Stop. This disables radius to perform the correct accounting statistics because radius is unable to map the start and end of the session. Can it be somehow enabled in ser to send User-Name parameter in the first message? Below is an example of such two corresponding accounting messages: Mon Mar 12 14:46:17 2007 SER-Attr = "" Acct-Session-Id = "9e6a674c-0fcf-db11-94ea-00148539376e@sen" Sip-To-Tag = "36974326" SER-From = "\"Sen Server\" <sip:tzl@voip.touk.pl>;tag=406e674c-0fcf-db11-94ea-00148539376e" SER-Flags = 8 SER-Original-Request-ID = "sip:110@voip.touk.pl" Sip-Method = "INVITE" Sip-Cseq = 2 Sip-Translated-Request-ID = "sip:hellboy@192.168.0.105:7060" Sip-Source-IP-Address = 192.168.0.165 Sip-From-Tag = "406e674c-0fcf-db11-94ea-00148539376e" SER-To = "<sip:110@voip.touk.pl>;tag=36974326" SER-Digest-Username = "tzl" SER-Request-Timestamp = 1173707170 Calling-Station-Id = "sip:tzl@voip.touk.pl" Sip-Source-Port = 5067 SER-Digest-Realm = "voip.touk.pl" Sip-Response-Code = 200 Called-Station-Id = "sip:110@voip.touk.pl" SER-Response-Timestamp = 1173707177 Acct-Status-Type = Start Service-Type = IAPP-Register NAS-Port = 5060 Acct-Delay-Time = 0 NAS-IP-Address = 127.0.0.1 Acct-Unique-Session-Id = "16bd1ddc2a514fa0" Timestamp = 1173707177 Mon Mar 12 14:47:10 2007 SER-Attr = "" Acct-Session-Id = "9e6a674c-0fcf-db11-94ea-00148539376e@sen" Sip-To-Tag = "36974326" SER-From = "\"Sen Server\" <sip:tzl@voip.touk.pl>;tag=406e674c-0fcf-db11-94ea-00148539376e" SER-Flags = 8 SER-Original-Request-ID = "sip:hellboy@192.168.0.105:7060" Sip-Method = "BYE" Sip-Cseq = 4 Sip-Translated-Request-ID = "sip:hellboy@192.168.0.105:7060" Sip-Source-IP-Address = 192.168.0.165 Sip-From-Tag = "406e674c-0fcf-db11-94ea-00148539376e" SER-To = "<sip:110@voip.touk.pl>;tag=36974326" SER-Request-Timestamp = 1173707230 Calling-Station-Id = "sip:tzl@voip.touk.pl" Sip-Source-Port = 5067 Sip-Response-Code = 200 Called-Station-Id = "sip:110@voip.touk.pl" SER-Response-Timestamp = 1173707230 Acct-Status-Type = Stop Service-Type = IAPP-Register User-Name = "tzl(a)voip.touk.pl" NAS-Port = 5060 Acct-Delay-Time = 0 NAS-IP-Address = 127.0.0.1 Acct-Unique-Session-Id = "4a9f1334616db4a4" Stripped-User-Name = "tzl" Realm = "voip.touk.pl" Timestamp = 1173707230

2 1

Re: [Serusers] SIP Accounting Module problem
by Greger V. Teigre 20 Mar '07

20 Mar '07

Copy serusers. Private emails that should go on SER end up in a different inbox and get lower priority... I'm not a solaris person, but ser logs to syslog. g-) POON Ben wrote: > Hi Greger, > > Thanks for the tip. I'm using Solaris 10 and whatever Ser version > it's bundled with, everything came preinstalled. I went to /var/log, > but there's no messages folder, all I have a syslog.# files. How can > I find out where the log messages are kept, if there are any at all? > Is that something I can set in the ser.cfg file? > > Thanks, > Ben > > ------------------------------------------------------------------------ > *From:* Greger V. Teigre [mailto:greger@teigre.com] > *Sent:* Friday, March 09, 2007 1:56 AM > *To:* POON Ben > *Cc:* serusers(a)lists.iptel.org > *Subject:* Re: [Serusers] SIP Accounting Module problem > > Ben, > the cat error just tells you that ser didn't start. Find the command > in your ser service script that actually starts ser and start it > manually. You may also add -E -D -D -D -D -D > to get lots of debug info to stderr (or just look in your > /var/log/messages) > g-) > > POON Ben wrote: >> Hi folks, >> >> I'm trying to get my accounting services working, but am having >> trouble doing so... I am using the sample ser.cfg file, and am >> having a problem loading the acc.so module. >> >> In the ser.cfg file, I try added the line: loadmodule >> "/usr/sfw/lib/ser/modules/acc.so" to the bottom of the loadmodule >> section. I haven't done any modparam or scripting yet, even so, when >> I restart the ser service, I get: Starting SER : cat: cannot open >> /var/run/ser.pid. >> >> If I comment or remove the loadmodule line, ser will load again. Is >> there anything else I need to add or configure before loading this >> module? I went to /usr/sfw/lib/ser/modules to make sure acc.so is >> there, and it is. >> >> Any help is greatly appreciated. Thank you very much. >> Ben >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Serusers mailing list >> Serusers(a)lists.iptel.org >> http://lists.iptel.org/mailman/listinfo/serusers >>

1 0

[Serusers] Change URI before accounting ?
by inge 20 Mar '07

20 Mar '07

Hi all, When I modify an URI by stripping some words, in ACC table I've got the old URI, before the stripping. So if INVITE contains sip:7000123456789, after strip he contains sip:0123456789, in acc I've INVITE ACK and BYE with sip:7000123456789. How can I solve it ? Thanks for your help. Regards, Adrien

3 11

[Serusers] SER home proxy with Asterisk voicemail
by Meidiana Ten 20 Mar '07

20 Mar '07

Hi guys, I'm give up with SEMS as media server for voicemail cause it can't successly run although I've followed how to install SEMS at http://ftp.iptel.org/pub/sems/doc/current/Configure-Sems-Ser-HOWTO.html and there is no answer for the problem So I decide to try Asterisk as the voicemail server. But I never use Asterisk before. I really need help in configuring Asterisk. What should I have (the softwares) before compiling and configuring Asterisk as voicemail server. Thanx for the attention. Regards, Meidiana ____________________________________________________________________________________ Expecting? Get great news right away with email Auto-Check. Try the Yahoo! Mail Beta. http://advision.webevents.yahoo.com/mailbeta/newmail_tools.html

5 9

[Serusers] Call forwarding
by Jai Rangi 20 Mar '07

20 Mar '07

Hello, I have a ser and asterisk setup. Users register on ser and all the national and international calls go through asterisk. Asterisk handles the billing part for long distance calls. Now I got an issue with call forwarding. Here is the situation. Useragent A calls Usergent B. User B has setup the call the call forwarding to his cell phone. So when user A calls user B, ser check that user B has set the forwarding and send the call to Asterisk box. Asterisk box sees user A in the callerID and bills user A for that call. We want user B to be billed for that call, cause he is forwarding the calls to his cell phone (long distance number). How can I achieve this. Thank you, -Jai

1 0

[Users] permissions module and avp definition
by Andreas Granig 19 Mar '07

19 Mar '07

Hi, It seems like most (all?) of the module params defining an AVP have changed from just the name (like "i:100") to a full avp spec (like "$avp(i:100)"). Does this also hold true for peer_tag_avp in permissions module? I ask because it's still "i:707" in the example of http://openser.org/docs/modules/1.2.x/permissions.html#AEN343 and it's not mentioned in http://openser.org/dokuwiki/doku.php/install:1.1.x-to-1.2.x Regards, Andreas This e-mail is confidential and may well also be legally privileged. If you have received it in error, you are on notice of its status. Please notify us immediately by reply e-mail and then delete this message from your system. Please do not copy it or use it for any purposes, or disclose its contents to any other person: to do so could be a breach of confidence. Thank you for your cooperation. Information pursuant to paragraph 14 Austrian Companies Code: UPC Austria GmbH; Registered Office: Wolfganggasse 58-60, 1120 Vienna Company Register Number: FN 189858d at the Commercial Court of Vienna

2 1

[Users] t_uac_dlg disconnect example - WILLING TO PAY
by Daryl Sanders 19 Mar '07

19 Mar '07

I need a complete example (with proper syntax) of how to disconnect a call (send BYE) using "t_uac_dlg". This can be either via bash script or openserctl command. I have been fighting with this for some time and always seem to get "Too few or to many parameters" errors. I have been through the ctd.sh example and searched the mailing list but, I'm still having no luck. I have read Jan's "SER FIFI Interface" doc, and I believe my fifo files are working properly, however I really don't know the exact syntax, or what elements are required to get this to work. I have access to the "Call-ID" as it is stored in MySQL via acc. I am willing to pay for this example. Just let me know a fair price. FYI: I am using OpenSER 1.2. Thanks, Daryl

2 1

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users