sr-users April 2022

sr-users@lists.kamailio.org

49 participants
63 discussions

Via header force change protocol to TLS?

by Anthony Alba

I have kamailio behind a TLS termination proxy so the sockets are correctly deduced to be TCP. However the clients only talk TLS to the proxy and are confused when the top Via header added by Kamailio is TCP. Is there a way for Kamailio to forcibly pretend its protocol is TLS? Like advertised_address but "advertised_protocol" instead. (With pjsip testing: it has a flag use_tls which ignores TCP from Kamailio and continues to use the persistent TLS transport to proxy. Linphone fails because it tries to honor TCP in Via and is unable to establish TCP transport). BTW I am using t_relay_to_tcp so Kamailio will return traffic to the proxy as TCP even though the contact addresses specify transport=TLS.

6 months

Dialog and DMQ on restart

by Björn Klasen

Hi everybody, I'm just testing Kamailio 5.4.1 with dialog replication over DMQ. This seems to work very good. Dialogs are replicated without problems. When I'm restarting one node I would have expected, that all dialogs are synced again, just like in dmq_usrloc. But this does not happen. After a restart the nodes dialog-list is empty. Did I miss somethin? Is there a special parameter that I have to set? BR, Björn -- Björn Klasen, Specialist TNG Stadtnetz GmbH, Network Management (VoIP) Projensdorfer Straße 324 24106 Kiel Germany T +49 431/ 530530 F +49 431/ 7097-555 mailto: bklasen(a)tng.de http://www.tng.de Register: Amtsgericht Kiel HRB 6002 KI Executive board (Geschäftsführung): Dr.-Ing. Volkmar Hausberg, Sven Schade, Carsten Tolkmit, Dr. Sven Willert Tax-Id (Steuernr.): 2029047020, VAT-Id (USt-Id): DE225201428

8 months, 1 week

Is Min-SE check broken?

by harneet singh

Hi All, I am facing an issue in understanding how the min_se should be working in kamailio. As per the SST documentation, it seems like if the min_se is configured as 500, then any value of Session-Expires OR MIN-SE if lower than 500, can be responded to by a 422. However, I strangely see the reverse happening. To investigate further, I looked in to the ki_sst_check_min() code in the master, and these seems like a potential issue. Ref Code: Inside ki_sst_check_min(), there is an if condition like below: if (sst_min_se < MIN(minse, se.interval)) { However, shouldn't it be the other way around? ie if (sst_min_se > MIN(minse, se.interval)) { because we need to send 422 if the received value(in INVITE etc) is smaller than the sst configure min_se value? I also found a different documentation, at https://git.sgu.ru/oldssu/ex-opensips/blob/cb9df8d59dbb254a9d862569fd5d11f6… where the check is as below? if (sst_min_se > MIN(minse, se.interval)) { Can someone confirm if this is broken, or my understanding is incorrect? Regards, Harneet -- "Once you eliminate the impossible, whatever remains, no matter how improbable, must be the truth" - Sir Arthur Conan Doyle

1 year, 6 months

Re: [SR-Users] TOPOS (5.1.[23]) breaks PRACK

by Daniel Tryba

On Mon, May 07, 2018 at 04:44:14PM +0200, Daniel Tryba wrote: > Sure. Attached. Problem appears to be that the topos query can't find > callid-totag (from the response). > > I'll try the same scenario with the mysql backend to see if it behaves > different. Config works fine with mysql as topos backend. So the bug is restricted to topos-redis.

1 year, 7 months

enable topology hiding on one side or dynamic ip in topoh module Contact and Via Header

by Patrick Karton

Hello , im using kamailio with two interfaces external and internal. i need a way either to : * enable topoh hiding only when outgoing interface is external ( mask contact and Via ip only when ougoing interface is external * or if it is not possible to enable it only in one direction.i want to know how to configure dynamic(for example in xavp or avp) ip to put in Contact and Via when topoh is enabled. i see that the 'mask_ip' parameter of topoh module is a string. so we can not set a dynamic value here unfortunately. Thanks

1 year, 9 months

kamcmd autocompletion

by Antoine DEBARRE

Hi, I just installed kamailio v5.5 via deb.kamailio.org packages (debian 11). Seems that kamcmd autocompletion doesn't work at all. It is OK for v5.4 via official debian packages (packages.debian.org/bullseye/kamailio) Best regards, -- <https://app.livestorm.co/comdata-group/metaverse-what-will-cx-look-like-in-…>

2 years

Possibility of mirroring the rpm/deb.kamailio.org repos efficiently via rsync?

by Malte Schmidt

Hello, is there an rsync endpoint available or is there a possiblity of setting this up? Creating a mirror via HTTP is a rather quick and dirty solution and while the deb-repo can be mirrored using debmirror, the rpm repo is hard to sync to a non-CentOS-based machine due to missing dependencies such as yum and reposync in latest Debian-based systems. Would be great to get some input in regards to this topic. Cheers

2 years, 5 months

Development for v5.6.x is frozen

by Daniel-Constantin Mierla

Hello, the formal notification that the development for the next major version 5.6.0 is now frozen. The focus has to be on testing the master branch. Also, the master branch should not get commits with new features till the branch 5.6 is created, expected to happen in 2-4 weeks, a matter of how testing goes on. Meanwhile, the commits with new features in the C code can be pushed to personal branches, new pull requests can still be done, but they will be merged after branching 5.6. Can still be done commits with documentation improvements, enhancements to related tools (e.g., kamctl, kamcmd), merging exiting pull requests at this moment, exporting missing KEMI functions and completing the functionality of the new modules added for 5.6. Once the branch 5.6 is created, new features can be pushed again to master branch as usual. From that moment, the v5.6.0 should be out very soon, time used for further testing but also preparing the release of packages. If someone is not sure if a commit brings a new feature, just make a pull request and it can be discussed there on github portal or via sr-dev mailing list. A summary of what is new in upcoming 5.6 is going to be built at: * https://www.kamailio.org/wiki/features/new-in-5.6.x Upgrade guidelines will be collected at: * https://www.kamailio.org/wiki/install/upgrade/5.5.x-to-5.6.0 Everyone is more than welcome to contribute to the above wiki pages, especially to the upgrade guidelines, to help everyone else during the migration process from v5.5.x to 5.6.x. Cheers, Daniel -- Daniel-Constantin Mierla -- www.asipto.com www.twitter.com/miconda -- www.linkedin.com/in/miconda

2 years, 6 months

Problem with Record-Route in Public to Private Network

by Carlos Escalona

Hello! I wish everyone who reads this message a good day. I would appreciate some guidance with the configuration of my Kamailio. Initially, I have the following architecture: Endpoints <----Public IP----> Kamailio (listen PrivateIP advertise PublicIP) <----Private IP----> Asterisk CONFIG: https://gist.github.com/Carlos-Escalona94/3a289af05b05c69ae563ab29c9ec4710 In general, calls initiated from outside the system work perfectly, but I have a problem with calls initiated from Asterisk. According to what I was able to investigate and understand, the problem arises from the fact that Kamailio uses the public IP for the entire routing system that involves the Record-Route and Route Headers. This in turn causes Asterisk to get lost trying to send messages outside of the INITIAL INVITE transaction, for example, the ACK response to the 200 Ok received from the Endpoint since it tries to use Kamailio's public IP to which Asterisk doesn't have access. I tried to force Asterisk to send all messages to Kamailio's private IP regardless of their nature, but it doesn't seem like an appropriate solution. On the other hand, I tried to modify the architecture a bit so that it was something similar to this: Endpoints <---- Public IP----> Kamailio (listen PrivateIP:P1 advertise PublicIP) <---- PrivateIP-----> Kamailio (listen PrivateIP:P2) <---- PrivateIP ----> Asterisk CONFIG: https://gist.github.com/Carlos-Escalona94/4d681bb189c6190941d291965e123889 It seems to me that this would solve the problem, but I have two doubts about this architecture, the first is that I would like to know if there is an easier way to solve the problem that I am not considering, and on the other hand, I have not found a way to identify from which interface is receiving the message to perform the routing properly. Thanks for the attention. -- *Esta mensagem pode conter informação confidencial ou privilegiada, sendo seu sigilo protegido por lei. Se você não for o destinatário ou a pessoa autorizada a receber esta mensagem, não pode usar, copiar ou divulgar as informações nela contidas ou tomar qualquer ação baseada nessas informações. Se você recebeu esta mensagem por engano, por favor, avise imediatamente ao remetente, respondendo o e-mail e em seguida apague-a. Agradecemos sua cooperação. ** * *This message may contain confidential or privileged information and its confidentiality is protected by law. If you are not the addressed or authorized person to receive this message, you must not use, copy, disclose or take any action based on it or any information herein. If you have received this message by mistake, please advise the sender immediately by replying the e-mail and then deleting it. Thank you for your cooperation. *

2 years, 6 months

Getting "uac.reg_add" to work (documentation unclarities)

by Rick van Rein

Hello, I am trying to make UAC register with a SIP telco. But when I run... shell$ kamctl rpc uac.reg_add mydomain.com 0123456789 myteldomain.com 0123456789 sip6.telco.nl telcoreseller.nl 999999 secretpw . udp:sip6.telco.nl 360 0 10 'udp:[fd8:9::10]:5090' ...it gives me the cryptic response... ERROR: jsonrpcs [jsonrpcs_mod.c:666]: jsonrpc_scan(): field is not a string - type 3 The module docs only give "..." as example of attributes. And, according to... http://www.kamailio.net/docs/modules/5.4.x/modules/uac.html#uac.r.uac.reg_a… https://github.com/kamailio/kamailio/blob/5.4.4/src/modules/uac/uac_reg.c#1… ...it also seems to be behind on diff_expires, timer_expires, reg_init. What I am missing is the format, and in some cases the purpose of attributes. Could you help me to an example, perhaps based on the command I am trying? Thanks, -Rick P.S. It's been years since I worked with OpenSIPS. It feels like Kamailio is friendlier, and easier to use.

2 years, 7 months

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users April 2022