sr-users February 2017

sr-users@lists.kamailio.org

74 participants
99 discussions

remove offline message prefix of Offline message of MSILO module
by Venkatesh Macha 16 Feb '17

16 Feb '17

Hi all, I am implementing Offline messages functionality using the MSILO module. Everything went well. I am able to store and send those offline messages when the user comes online. But my present problem is, I don't want the offline message prefix. Please look at the following example. This is what Kamailio sending. [Offline message - Wed Feb 15 05:43:38 2017] Test2 I want only Test2 Is there any possibility to remove that offline message prefix ? Thank you in advance ! -- View this message in context: http://sip-router.1086192.n5.nabble.com/remove-offline-message-prefix-of-Of… Sent from the Users mailing list archive at Nabble.com.

2 2

Timejump causes kamailio to hang/stall
by Erik Visser 16 Feb '17

16 Feb '17

After I have kamailio up and running, with UAs properly registrered and sessions routed successfully, my platform faces a timejump. The platform starts up with date&time set to 1-1-2000 and after kamailio is up and running, the date&time jumps to the current date&time, causing two effects: - I loose all my registrations (since they expired in 3600 seconds) - kamailio does not respond to any SIP messages for a couple of minutes Is there a way to have kamailio use timeticks rather than relative time for the registrations? Does anybody recognize the hanging behavior? Any suggestions? Thanks! Erik ____________________ Erik Visser erik(a)vissershut.nl

2 1

IPv6 addresses in dispatcher.list file
by Joel Serrano | VOZELIA 16 Feb '17

16 Feb '17

Hi, What is the correct format for the dispatcher.list file using IPv6? I have the following file: $ cat /etc/kamailio/dispatcher.list # $Id$ # dispatcher destination sets # # line format # setit(int) destination(sip uri) flags(int,opt) priority(int,opt) attributes(str,opt) # proxies 4 sip:XX.XX.XX.XX:5060 4 sip:ZZ.ZZ.ZZ.ZZ:5060 6 sip:[X:X:X:X::X:1]:5060 6 sip:[Z:Z:Z:Z::Z:2]:5060 $ For some reason, Kamailio doesn't recognize the v6 endpoints: kamcmd> dispatcher.list { NRSETS: 1 RECORDS: { SET: { ID: 4 TARGETS: { DEST: { URI: sip:XX.XX.XX.XX:5060 FLAGS: AP PRIORITY: 0 } DEST: { URI: sip:ZZ.ZZ.ZZ.ZZ:5060 FLAGS: AP PRIORITY: 0 } } } } } kamcmd> I have tried multiple combinations for the v6 format but I cannot get one to work. What am I doing wrong? Thanks, Joel. Este mensaje y, en su caso, los ficheros anexos son confidenciales, especialmente en lo que respecta a los datos personales, y se dirigen exclusivamente al destinatario referenciado.Les informamos que los datos contenidos en el presente mail, han sido facilitados por usted o recogidos de Fuentes Accesibles al Público. Dicha información personal, será incluida en un fichero bajo la responsabilidad de VOZELIA TELECOM S.L.Todos los ficheros que trata nuestra empresa se encuentran debidamente inscritos ante la Agencia Española de Protección de Datos.Vd. Como propio interesado podrá ejercitar sus derechos de Acceso, Cancelación, Rectificación u Oposición, en el mail: administracion(a)vozelia.com o en la dirección Avenida de Manoteras 8 escalera 3 2ºB, 28050 Madrid.Tal y como establece la Ley Orgánica de Protección de Datos 15/1999 de 13 de Diciembre.Para ejercer sus derechos desde Panama podrá hacerlo en la dirección Vía Argentina, Edificio Mediteranean Loft. Panama.En caso de no ser el destinatario y haya recibido este mensaje por error, agradeceremos que nos lo comunique inmediatamente al remitente sin difundir, almacenar o copiar su contenido.La divulgación o el suministro, en todo o en parte, a cualquier tercero, no podrá ser realizada sin el previo, expreso y escrito consentimiento de VOZELIA TELECOM S.L. .

2 1

record_route() function
by Andy Chen 15 Feb '17

15 Feb '17

Hi all, I need some advise on how to use the record_route() function. So I make that call when the first method comes in and there are two Record-Route headers created. However, one of of the headers I want to add transport=tcp. What is the best way to do this? I've tried adding that string per documentation within the () and added it to both. Thanks. -- Andy Chen

3 10

Branch 5.0 created
by Daniel-Constantin Mierla 15 Feb '17

15 Feb '17

Hello, the GIT branch 5.0 has just been created, it will host the release series 5.0.x. To get this branch from GIT, you can use: git clone https://github.com/kamailio/kamailio.git kamailio cd kamailio git checkout -b 5.0 origin/5.0 Hopefully before the end of the month the full release of 5.0.0 will be out. >From now on, any corresponding fix has to be pushed first to master branch and then cherry-picked to branch 5.0. No new features can get in branch 5.0. Enhancements to documentation or helping tools are still allowed. If you are not sure about doing or not a backport, ask on sr-dev mailing list. Cheers, Daniel -- Daniel-Constantin Mierla www.twitter.com/miconda -- www.linkedin.com/in/miconda Kamailio Advanced Training - Mar 6-8 (Europe) and Mar 20-22 (USA) - www.asipto.com Kamailio World Conference - May 8-10, 2017 - www.kamailioworld.com

4 9

Dispatcher and "src based" routing algorithm
by Olli Attila 15 Feb '17

15 Feb '17

Hello, I am using kamailio 4.4.3 (x86_64/linux) 5a2195 and Dispatcher module to route calls towards PSTN (4 pstn gateways). The Dispatcher module is using round robin mechanism to select the pstn gateway. I have built a routing logic in a way that when call arrives to Kamailio from one of the PSTN gateways, and fails to route towards an external sip target, the call is marked as CFU call (a diverting call) and routed back to PSTN with different B number, but the actual challenge is that I would like the target PSTN gateway _not_ to be the same PSTN gw from where the call originally came in to Kamailio. This feature is requested because of the technical limitations of the pstn gateway software. So is there any mechanism in Dispatcher or elsewhere in Kamailio to do this? Basically I would need a flag or something to mark the pstn gateway when the call comes in and assure that when routing back to pstn, the same gateway would not be used at all, or it should be used as last target from the four gateways in Dispatcher. Cheers, -- Olli

1 0

Refreshing: info about private emails
by Daniel-Constantin Mierla 15 Feb '17

15 Feb '17

As I still receive a lot, I am re-posting the notification about private emails, either initiating a topic or sent directly after a discussion started on public mailing lists (subject with mailing lists prefix, but the sender header is not the mailing list daemon). I would like to remind that, at least in my case, writing emails directly without cc-ing the mailing list is highly not recommended. The rule is also suggested in the mailing lists presentation page: - http://www.kamailio.org/w/mailing-lists/ Unless I asked explicitly for a private email with some specific details, the message will not be noticed in decent time and therefore not replied. I use this email address for many public mailing lists and it is intended only for that usage, I am reacting based on the filters I created, unmatched messages getting the lowest priority. Therefore if you wrote me and expect a response, re-send the message to the appropriate public mailing list. Checking and answering the messages on Kamailio mailing lists are among the top of priorities on my daily activity, so it is high chance you get the response faster when you write there. Note that you can always mask sensitive data (e.g., replace passwords, IP addresses) before sending logs or config file. There are several common sense as well as technical reasons for keeping the discussion on public mailing lists. Here are some along with other suggestions to improve the likeliness of getting an answer: - we are not answering questions on mailing lists to help only one person, but also other people that may have similar issues in the future -- they can find the answers in the archive with a search engine. Also, other people subscribed to the list can learn from conversation or contribute to the discussion, resulting in better outcome - the amount of unexpected messages is very high -- it is practically a zero chance to get to the folder with messages that didn't match any filter (thus your message is not going to be replied) - whenever I find time, the first emails I answer are those coming on mailing lists. They are many there as well, people are traveling or having other personal or business projects, so sometime is good to send a reminder if a question does not get an answer - starting with negative approach or no technical content, like you are going to use something else if you don't get this instantly, or this application is missing what so ever tutorial giving exactly the solution you need, or simply asking for full config of complex requirements, is not helping at all, but actually making people to ignore your messages. Start with what you tried and where you got stuck. Everything you get is for free, have appropriate expectation and behavior. Cheers, Daniel -- Daniel-Constantin Mierla www.twitter.com/miconda -- www.linkedin.com/in/miconda Kamailio Advanced Training - Mar 6-8 (Europe) and Mar 20-22 (USA) - www.asipto.com Kamailio World Conference - May 8-10, 2017 - www.kamailioworld.com

1 0

TOPOH MODULE
by Annus Fictus 14 Feb '17

14 Feb '17

Hello, I'm using TOPOH module but I have a problem with Call-ID. If I use: modparam("topoh", "mask_callid", 1) and send the INVITE to a media server, when media server send BYE to KAMAILIO, Kamailio answer like transaction not exist. In the parameter description, I read i have to use "lreq_callee_headers" dialog parameter to resolve this kind of issues, but I can't find this parameter on the module description. I'm using Kamailio 4.4.5 Thank's Regards

3 3

Remove
by Ryan Holbein 13 Feb '17

13 Feb '17

Can you please remove me

2 1

SIP-T conversion to SIP
by Martin Quevedo 13 Feb '17

13 Feb '17

hi all I need to interact with an MSC that talks SIP-T that is the MSC embeds ISUP in the SIP messages IAM, ANM, ACM and REL messages specifically but I have a SIP client which does not speak SIP-T is it possible that kamailio parses invites with IAM ISUP parameters like forwarding number and forwarding reason for incoming messages and embeds ACM, ANM and REL isup messages in OK, Session Progress and BYE regards, Martin ?

1 0

← Newer
1
2
3
4
5
6
7
8
9
10
Older →

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users February 2017