sr-users July 2005

sr-users@lists.kamailio.org

199 participants
544 discussions

by Nicky

Dear all, Anyone encountered the problem below,please help. Thank you. ----- Original Message ----- From: Nicky To: sems(a)lists.iptel.org ; serusers(a)lists.iptel.org Sent: Thursday, June 16, 2005 3:51 PM Subject: Problem on pthread and dtmf Dear all, 1. Please help, when i run sems -E i experienced this error, what can be the caused of it:~ ~~11352) ERROR: start (AmThread.cpp:73): pthread create failed with code 12 2. There is signal of DTMF which is not pressed but is being send to the server, please see below for the log. Please advice what can be the caused and problem. Thank you in advance. ~~(4395) DEBUG: isdn_audio_eval_dtmf_relative (IvrDtmfDetector.cpp:349): Posting D TMF 0: 5 (5) (4395) DEBUG: postEvent (AmEventQueue.cpp:47): AmEventQueue: trying to post even t (4395) DEBUG: postEvent (AmEventQueue.cpp:55): AmEventQueue: event posted (4395) DEBUG: processEvents (AmEventQueue.cpp:68): before processing event (4395) DEBUG: process (IvrPython.cpp:988): IvrPython processing event... (4395) DEBUG: process (IvrPython.cpp:991): IvrDialog processing event... (4395) DEBUG: onDTMFEvent (IvrPython.cpp:1130): IvrPython::onDTMFEvent(): callin g onDTMFCallback key is 5... (4395) DEBUG: ivrEmptyMediaQueue (IvrPython.cpp:102): IVR: emptying media queue . (4395) DEBUG: IvrMediaEvent (IvrEvents.cpp:31): New Media Event: 1, (4395) DEBUG: postEvent (AmEventQueue.cpp:47): AmEventQueue: trying to post even t (4395) DEBUG: postEvent (AmEventQueue.cpp:55): AmEventQueue: event posted (4395) DEBUG: ivrStopRecording (IvrPython.cpp:132): IVR: stop recording. best regards, nicky

18 years, 10 months

[Serusers] Serctl Alias Format

by Aisling

Hello, Can someone tell me if the format for adding user aliases has changed? I am trying to create an alias (serctl alias add 1234 sip:1234dt@xxx.xxx.xxx.xxx) and an error 400 ul_add flags expected is happening. Many Thanks, Aisling. -------------------Legal Disclaimer--------------------------------------- The above electronic mail transmission is confidential and intended only for the person to whom it is addressed. Its contents may be protected by legal and/or professional privilege. Should it be received by you in error please contact the sender at the above quoted email address. Any unauthorised form of reproduction of this message is strictly prohibited. The Institute does not guarantee the security of any information electronically transmitted and is not liable if the information contained in this communication is not a proper and complete record of the message as transmitted by the sender nor for any delay in its receipt.

18 years, 10 months

RE: [Serusers] Pbm solved: serctl : error: 400; check if you use aliases in SER

by Rodrigue ESTEVE

Hi TC, Ok this solved my pbm. Thanks a lot. Rodrigue, -----Message d'origine----- De : TCCHAN [mailto:tikchoong.chan@redtone.com] Envoyé : mardi 5 juillet 2005 05:57 À : Rodrigue ESTEVE Objet : [Serusers] serctl : error: 400; check if you use aliases in SER Hi, You need to add lookup("aliases") in your script. I had this problem before. Regards, TC Chan

18 years, 10 months

RE: [Serusers] Pbm Solved :Mysql with a different password than heslo

by Rodrigue ESTEVE

Hi Sandra, and the others, I found the solution to my pbm, in a previous test configuration I commented the modparam for acc module, if you look at the syslog in my previous message, the error is related to the loading of the acc module looking for the default password cause I forgot to set the modparam (in fact the conf is commented). For those who have pbm with sql password take a deeper look (than me) to the syslog message. Thanks for this great user list, and sorry for the kiddy pbm :) Rodrigue -----Message d'origine----- De : sandrad(a)tid.es [mailto:sandrad@tid.es] Envoyé : mardi 5 juillet 2005 11:12 À : Rodrigue ESTEVE Objet : Re: [Serusers] Mysql with a different password than heslo Hi Rodrigue! I've change tha pass too, and in the cfg I only specify the param of usrloc: modparam("usrloc", "db_url", "sql://ser:newpass@localhost/ser") And its run ok, This and the param of msilo. Rodrigue ESTEVE escribió: > Hi all, > > I've got a pbm using mysql with ser 0.9.3 when I set a password > different from the default passwd heslo for ser user. > > When using the default password configuration and the ser_mysql.sh > script, I've got no pbm. I can use the localhost database and even a > database started on another proxy with a different password than heslo > (heslo2), using the settings below in ser.cfg: > > fifo_db_url="mysql://ser2:heslo2@172.30.30.104/ser2" > > modparam("auth_db|uri_db|usrloc", "db_url", > "mysql://ser2:heslo2@172.30.30.104/ser2") > > But when I modify the ser_mysql.sh to use a different password than > heslo (heslo 2 for example, see below), ser does not start using: > > fifo_db_url="mysql://ser:heslo2@localhost/ser" > > modparam("auth_db|uri_db|usrloc", "db_url", > "mysql://ser:heslo2@localhost/ser"). > > Moreover I'm now unable to log to the database loaded on the other > proxy (172.30.30.104) using the first configuration above. > > When using mysql -h localhost -u ser -p and using the new password, I > can connect to the database. > > The syslog shows this when trying with a different password: > > Jul 4 18:56:34 sip /sbin/ser[7155]: new_connection(): Access denied > for user: 'ser@localhost' (Using password: YES) > > Jul 4 18:56:34 sip /sbin/ser[7155]: db_init(): Could not create a > connection > > Jul 4 18:56:34 sip /sbin/ser[7155]: ERROR: acc_db_init: unable to > connect to the database > > Jul 4 18:56:34 sip /sbin/ser[7155]: init_mod_child(): Error while > initializing module acc > > Jul 4 18:56:34 sip /sbin/ser[7155]: init_child failed > > Jul 4 18:56:34 sip /sbin/ser[7155]: WARNING: destroy_fifo: cannot > delete fifo (/tmp/ser_fifo): No such file or directory > > Does somebody can help me; I'm trying to get this working without success. > > Thanks a lot, > > Rodrigue > >------------------------------------------------------------------------ > >_______________________________________________ >Serusers mailing list >serusers(a)lists.iptel.org >http://lists.iptel.org/mailman/listinfo/serusers > > -- Sandra Donaire Arroyo Telefónica I+D División de "Tecnologías de acceso a redes IP"

18 years, 10 months

Re: [Serusers] SerWeb0.9.3 show me the error :DB Error: no such table Why?

by Karel Kozlik

Hello, please (CC) the list in your replies. I exactly don't know why there is a "DB Error: syntax error". May be you have some older version of mysql. Serweb needs mysql >= 4.0. You may also try enable logging in serweb by set config variable $config->enable_loging to true. In log file you will see sql queries and more descriptive error messages. Please send me it. Karel zhaomin napsal(a): > Thank you Karel,I resolve one question that show "DB Error: no such table" by your guidance.but I have a new question now it is when I want to show accounting and missed calls .it's show me "DB Error: syntax error" why that's for? > ZhaoMin > ----- Original Message ----- > From: "Karel Kozlik" <karel(a)iptel.org> > To: "zhaomin" <zhaomin(a)kingdream.com> > Cc: <serusers(a)lists.iptel.org> > Sent: Monday, July 04, 2005 7:39 PM > Subject: Re: [Serusers] SerWeb0.9.3 show me the error :DB Error: no such table Why? > > > >>Hello, >>ser-0.9.3 and ser cvs useing a little diferent DB schema. There is a >>confusion in names of tables for user preference. Check the names of >>tables in config/config_data_layer.php and match them with you DB schema. >> >>Karel >> >>zhaomin napsal(a): >> >>>I used serweb-0.9.3 and Ser CVS version, I can register and login but >>>when I login and open the my account show me error: DB Error: no such >>>table.but it's can open the data in the mysql .I have this error prompt >>>at many place include admin,anyone have this prompt? How can I resolve it? >>> Thanks advance ! >>> ZhaoMin >>> >>> >>>------------------------------------------------------------------------ >>> >>>_______________________________________________ >>>Serusers mailing list >>>serusers(a)lists.iptel.org >>>http://lists.iptel.org/mailman/listinfo/serusers

18 years, 10 months

Re: [Serusers] call transfer INVITE / REFER

by Samuel Osorio Calvo

The effective transferring is done using REFER messages but since there are several transfer methods, some INVITEs can be triggered before (put on-hold, contact the referee). So, depending on how the user has configured the transfer in his/her phone (blind, attended, unattended,are there more??) the SIP request that the phone sends when the user presses the button is different. Take a look at the draft specifying the different transfer methods for a detailled view of the message flows (draft-ietf-sipping-service-examples I don't remember the most recent number....probably 7 or 8) Samuel. Unclassified. >>> Iqbal <iqbal(a)gigo.co.uk> 07/05/05 03:57AM >>> which is why I am wondering if on pressing a transfer button request on a phone, should the first message being sent be a REFER or a INVITE, cause refer would make sense, although I havent looked at the rfc, If anyone has a IP phones transferring a ngrep of transfer would be appreciated Iqbal On 7/4/2005, "Nils Ohlmeier" <lists(a)ohlmeier.org> wrote: >Hi, > >take a look at the SDP of the INVITE. Probably it just puts the other side >on-hold before sending the REFER. >But I have no real clue how transfering without REFER should work. (Except a >cumbersome solution with Replaces and 3pcc, which I have never.) > > Nils > >On Monday 04 July 2005 21:07, Iqbal wrote: >> Hi >> >> Should the call transfer use INVITE or REFER as a method, cause I seem, >> to be getting INVITE, but this then causes problems with authentication. >> >> A <-->B then B transfer to C (all IP phones) >> >> This transfer seems fine, but it uses INVITE, no REFER . All phones on >> same sip domain/server >> >> Now when this setup changes >> >> pstn <---->B and then B tried to transfer to C, we get nothing, well we >> get 404 , it check the !location setting, and says ur not allowed. >> >> Is the REFER the first message to be sent, or is there a INVITE >> transaction first, >> >> Iqbal >> >> >> _______________________________________________ >> Serusers mailing list >> serusers(a)lists.iptel.org >> http://lists.iptel.org/mailman/listinfo/serusers > > _______________________________________________ Serusers mailing list serusers(a)lists.iptel.org http://lists.iptel.org/mailman/listinfo/serusers

18 years, 10 months

[Serusers] nat_uac_test

by Chia Huey Lim

Hi, Can we determine what type of NAT environment UA is from by doing nat_uac_test alone ? i can't use STUN and am stuck in solving the NAT issue, as I can't distinguish whether UA is from symmetric NAT. Anyone has any clue other than using STUN? Thanks in advance Regards, Chia

18 years, 10 months

[Serusers] sharing a db server with two SER

by harry gaillac

Hello, I want to use a dedicated ser+sems dedicated server SER1---DB---SER2+SEMS When i start SER2 I get : serveur2:/etc/ser# tail /var/log/syslog Jan 1 03:50:06 serveur2 /usr/sbin/ser[1086]: Maxfwd module- initializing Jan 1 03:50:06 serveur2 /usr/sbin/ser[1086]: new_connection(): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) Jan 1 03:50:06 serveur2 /usr/sbin/ser[1086]: db_init(): Could not create a connection Jan 1 03:50:06 serveur2 /usr/sbin/ser[1086]: register_udomain(): Can not open database connection Jan 1 03:50:06 serveur2 /usr/sbin/ser[1086]: domain_fixup(): Error while registering domain Jan 1 03:53:36 serveur2 /usr/sbin/ser[1094]: Maxfwd module- initializing Jan 1 03:53:36 serveur2 /usr/sbin/ser[1094]: new_connection(): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) Jan 1 03:53:36 serveur2 /usr/sbin/ser[1094]: db_init(): Could not create a connection Jan 1 03:53:36 serveur2 /usr/sbin/ser[1094]: register_udomain(): Can not open database connection Jan 1 03:53:36 serveur2 /usr/sbin/ser[1094]: domain_fixup(): Error while registering domain //////////////////////////////////////////////// ser.cfg: port=5060 children=4 fifo="/tmp/ser_fifo" fifo_db_url="mysql://ser:heslo@serveur1.home.net/ser" user=ser group=ser fifo_user=ser # owner of the ser fifo fifo_group=ser fifo_mode=0660 # fifo's permissions #disable_core=yes #disables core dumping #open_fd_limit=1024 # sets the open file descriptors limit #mhomed=yes # usefull for multihomed hosts, small performance penalty #disable_tcp=yes #tcp_accept_aliases=yes # accepts the tcp alias via option (see NEWS) listen=192.168.0.2 ************** # -- auth params -- # Uncomment if you are using auth module # modparam("auth_db", "db_url", "mysql://ser:heslo@serveur1.home.net/ser") modparam("auth_db", "calculate_ha1", yes) Regards harry ___________________________________________________________________________ Appel audio GRATUIT partout dans le monde avec le nouveau Yahoo! Messenger Téléchargez cette version sur http://fr.messenger.yahoo.com

18 years, 10 months

[Serusers] voicemail with sems and ser 0.9.3 ser.cfg from onsip.org

by Rosario Pingaro

Hi I have configured ser and sems to have voicemail on my customers. To work with natted us I use mediaproxy and the ser.cfg from onsip.org Everything works fine when an user is offline, but when I try to use a failure route I am not able to get it working on natted custmers. The failure route is: failure_route[1] { if (t_check_status("408|486|480")){ ## Do not include 487!! lookup("aliases") ; rewritehostport("voip.italycomnet.it:5090"); append_branch(); t_relay(); break; }; } It is called on route(1): route[1] { t_on_reply("1"); if (!t_relay()) { if (method=="INVITE" || method=="ACK") { end_media_session(); }; sl_reply_error(); }; if (isflagset(4)) { t_on_failure("1"); }; } This is the sems log whe i call a natted us: (32382) DEBUG: write_to_fifo (SerClient.cpp:249): Write to fifo: completed (32382) DEBUG: getReturnCode (AmRequest.cpp:367): response from Ser: 200 fifo_t_reply succeeded (32382) DEBUG: setRAddr (AmRtpStream.cpp:394): RTP remote address set to 213.178.208.130:13652 (32382) DEBUG: negotiate (AmSession.cpp:184): Sending Rtp data to 213.178.208.130/13652 (32382) DEBUG: onSessionStart (AnswerMachine.cpp:316): starting sending announce...(/usr/local/apache2/htdocs/html/audio/default_en.wav) (32382) DEBUG: trying to read WAV file (32382) DEBUG: tag = <RIFF> (32382) DEBUG: file size = <391108> (32382) DEBUG: tag = <WAVE> (32382) DEBUG: tag = <fmt > (32382) DEBUG: chunk_size = <16> (32382) DEBUG: fmt = <01> (32382) DEBUG: channels = <1> (32382) DEBUG: rate = <8000> (32382) DEBUG: bits/sample = <16> (32382) DEBUG: tag = <data> (32382) DEBUG: chunk size = <391072> (32382) DEBUG: run (AmServer.cpp:158): version= <0.3> (32382) DEBUG: run (AmServer.cpp:168): fct_name= <sip_request.bye> (32382) DEBUG: execute (AmServer.cpp:226): cmd.method= <BYE> (32382) DEBUG: execute (AmServer.cpp:227): cmd.user= <voicemail+cyber> (32382) DEBUG: execute (AmServer.cpp:228): cmd.domain= <213.178.216.45> (32382) DEBUG: execute (AmServer.cpp:229): cmd.dstip= <213.178.216.45> (32382) DEBUG: execute (AmServer.cpp:230): cmd.port= <5090> (32382) DEBUG: execute (AmServer.cpp:231): cmd.r_uri= <sip:voicemail+cyber@213.178.216.45:5090> (32382) DEBUG: execute (AmServer.cpp:232): cmd.from_uri= <sip:6294209153@213.178.208.130> (32382) DEBUG: execute (AmServer.cpp:233): cmd.from= <"anonymous" <sip:6294209153@213.178.208.130>> (32382) DEBUG: execute (AmServer.cpp:234): cmd.to= <<sip:08281895128@voadsl.italycomnet.it>;tag=00007E7E32D96353> (32382) DEBUG: execute (AmServer.cpp:235): cmd.callid= <462465ae31a409b34ac2ccba108ed51d(a)213.178.208.130> (32382) DEBUG: execute (AmServer.cpp:236): cmd.from_tag= <as759a2b45> (32382) DEBUG: execute (AmServer.cpp:237): cmd.to_tag= <00007E7E32D96353> (32382) DEBUG: execute (AmServer.cpp:240): cseq_str= <103> (32382) DEBUG: execute (AmServer.cpp:245): cseq= <103>(103) (32382) DEBUG: execute (AmServer.cpp:247): cmd.key= <21048:437100943> (32382) DEBUG: execute (AmServer.cpp:248): cmd.route= <<sip:213.178.216.45;ftag=as759a2b45;lr=on>> (32382) DEBUG: execute (AmServer.cpp:249): cmd.next_hop= <sip:213.178.216.45;ftag=as759a2b45;lr=on> (32382) DEBUG: execute (AmServer.cpp:255): hdrs: `P-MsgFlags: 0 ' (32382) DEBUG: execute (AmServer.cpp:262): body: `' (32382) DEBUG: execute (AmServer.cpp:275): everything is OK ! (32382) DEBUG: sadSession (AmSession.cpp:358): searching for session to destroy (hash=462465ae31a409b34ac2ccba108ed51d(a)213.178.208.130as759a2b45,sess_key=00007E7E32D96353) (32382) DEBUG: findSession (AmSession.cpp:421): session found with key (32382) DEBUG: destroySession (AmSession.cpp:380): sess_it != a_sessions.end() (32382) DEBUG: destroySession (AmSession.cpp:383): it != sess_it->second.end() (32382) DEBUG: destroySession (AmSession.cpp:390): session found: stopping session (32382) DEBUG: stopAndQueue (AmSession.cpp:338): session cleaner trying to stop 32382 (32382) DEBUG: stop (AmThread.cpp:93): Thread 32382 calling on_stop, give it a chance to clean up. (32382) DEBUG: postEvent (AmEventQueue.cpp:47): AmEventQueue: trying to post event (32382) DEBUG: postEvent (AmEventQueue.cpp:55): AmEventQueue: event posted (32382) DEBUG: stop (AmThread.cpp:107): Thread 32382 finished detach. (32382) DEBUG: destroySession (AmSession.cpp:394): session stopped and destroyed (#sessions=0) (32382) DEBUG: write_to_fifo (SerClient.cpp:242): write_to_fifo: <:t_reply:00007E7E6EEFE477 200 OK 21048:437100943 00007E7E32D96353 Contact: <sip:bye+cyber@213.178.216.45:5090> Seems that the body is missing but I don't understend why??? Any help? Thanks Rosario

18 years, 10 months

[Serusers] multi-domain, partitions, multi-branding on 0.9.3 ?

by Jose Bertuzzi

Hello guys, how do you think it is the best way to implement some kind of partitions on ser? I mean, extensions 1000 to 1999 belong to domainA and can't call to extensions 2000 to 2999 on domainB. Also there are independent dialing plans for each domain. >From domainA to access international destinations 00+E164 should be dialed and from domainB 011+E164. Do you have an example of doing this? kind regards, Pablo __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

18 years, 10 months

← Newer
1
...
47
48
49
50
51
52
53
54
55
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

sr-users July 2005