Hi
I am doing the following and for some reason it doesn't seem to work
(please ignore syntax)
if (uri=0[1-9] { substr/^0/00/}
and then
if {uri=00)
Now should the second if statement now match, or not, it my config it
doesn't seem to.
iqbal
Hi
-----------------------------
failure_route[1]
{
if (t_check_status("408|500|503"))
{
t_reply("503", "Sorry");
}
}
-----------------------------
Is it posible to add loging in failure route, so User get 503, but I get
acctual info on what happen, because $rs $rr work only in onreply_route, but
I need them or any equivalent in failure_route? So I can log exactly what
happen.
Regards,
Taras
Hi
Im using
avp_write("sip:123456@1.2.3.4:4321", "i:100");
avp_pushto("$ruri","i:100");
t_relay();
And this is sended to 1.2.3.4:4321
like :
INVITE sip:123456@1.2.3.4:4321 SIP/2.0
And this works fine.
However can I make it some how to generate message like this :
INVITE sip:123456 SIP/2.0 ???
Or in this case I need to use :
avp_write("sip:123456", "i:100");
avp_pushto("$ruri","i:100");
t_relay_to_udp("1.2.3.4","4321");
Regards,
Taras
Hello all,
Hate to be a bother to the list, but the documentation for the LCR
module (and googling afterwards) left me slightly puzzled. . . The way I
read it, it seems like EVERY user on the system would have to have an
entry in the gw table, in order to match the FROM URI and get a gateway
prioritized....
Anyone have some light to shed on LCR? Maybe a solid doc somewhere?
Other than that, please keep up the excellent work! O_SER is definitely
a wonderful piece of work!
SKM
Hello, all:
I am using SER interworking with Cisco26 as PSTN gateway. So far,
everything goes OK but the Radius billing. There is only STOP Radius request
with no START Radius request at first. I think it's due to 183 with SDP
issue. But it seems early_media in ACC module didn't give it a remedy.
BTW, START/STOP runs OK in intra-domain call..which including 180 without
SDP in signaling loop.
My ser.cfg is as below:
modparam("acc", "log_level",1)
modparam("acc","radius_flag",1)
modparam("acc","radius_config","/usr/local/etc/radiusclient-ng/radiusclient.conf")
modparam("acc",report_ack",0)
modparam("acc",early_media",1)
# failed_transaction,report_cancels,radius_missed_flag...[uncommented]
Who can rescue me?
Thanks.
We are trying to use SEMS along with SER in our lab setup
We have configured a dedicated SEMS for one IP phone to start with
And enabled the announcement plug-in
But the announcement message is not played
Where does SEMS take the default player from?
Thanks
Hemal
Confidentiality Notice
The information contained in this electronic message and any attachments to this message are intended
for the exclusive use of the addressee(s) and may contain confidential or privileged information. If
you are not the intended recipient, please notify the sender at Wipro or Mailadmin(a)wipro.com immediately
and destroy all copies of this message and any attachments.
On 11/13/05, serge messa <sergepmessa(a)yahoo.fr> wrote:
> Hi
>
> Thanks for your reply. must i make changes in the
> mediaproxy.ini , the mediaproxy.cfg or openser.cfg
> file?
I had to configure mediaproxy.ini, but I am running mediaproxy on a
few different, boxes. You might not if you are only running it local.
Can anyone confirm this?
> I want to know if my openser.cfg config file have any
> problem?
>
> Have you use openser with the mediaproxy module? If
> so, send me your openser.cfg file and tell me how you
> make it work.
I am currently testing the onsip.org ser.cfg, and it works fine with
mediaproxy. If you have not done so you really should read the
onsio.org getting started docs. The mediaproxy info was very helpful
to me.
> Ps: i have some problem with my email
> messa(a)innsof.com. This is my alternate e-mail.
>
> best regards!
>
> Serge
>
>
>
>
>
>
> ___________________________________________________________________________
> Appel audio GRATUIT partout dans le monde avec le nouveau Yahoo! Messenger
> Téléchargez cette version sur http://fr.messenger.yahoo.com
>
Dear serusers,
I am running ser 0.9.3
I want to enable the accounting package to write to MySQL. I realize I need
to recompile to do this.
Can I just compile ONLY the acc and somehow install this acc module? If so,
how?
Is it just easier or better to recompile all of SER?
________________________________
Telecom CTO
Leo Papadopoulos
10 Old Stone Court
Ridgefield, CT 06877
Tel: 203-438-8117
Cell: 203-788-6364
E-mail: leo(a)telecomCTO.com
Web site: www.telecomCTO.com
Any idea what I might be doing wrong?
I have had some issues with setting up the served domain. I use x-lite for my SIP UAs and have to put the host name of my SER server to get them to log in, even though I set the environment variable for the SIP domain of the server to my domain. Do you think that it might be related?
Thanks,
George
>>> "Greger V. Teigre" <greger(a)teigre.com> 11/11/2005 12:19:59 AM >>>
I believe the standard NAT traversal configs from onsip.org should handle
that.
g-)
----- Original Message -----
From: "George Lambson" <LambsonGE(a)mtc.byu.edu>
To: <serusers(a)lists.iptel.org>
Sent: Friday, November 11, 2005 12:51 AM
Subject: [Serusers] mediaproxy for incoming
> Is anyone using mediaproxy for INCOMING calls?
>
> What I mean is: is SER capable of accepting INVITE messages from an
> unregistered UA that is behind a NAT Firewall and connecting them with a
> registered UA?
>
> I would like to be able to receive incoming calls for my domain from
> anyone on the internet and connect them to the proper user. Please tell me
> anyone if you are successfully doing this.
>
> Thanks,
> George
>
> _______________________________________________
> Serusers mailing list
> serusers(a)lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
>
_______________________________________________
Serusers mailing list
serusers(a)lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers
