FW: FW: [Serusers] DNS SRV Mediaproxy

[Richard C. Thompson]

Thanks Samuel

I now have it working. I found out the proxydispatcher was using eth0 which
had the other IP address on it. The one that SER is not listening on. Once I
switched the IP addresses around it started working. BTW in order to get SER
to route calls I had to turn mhomed off. Normally I use bond0 with two
Ethernet interfaces, multihome on and use roundrobin to provide redundancy
but in this case I am trying to set up two SER servers, one as a mirror of
the other for a hot standby. I want to sync the two mysql databases using
the eth1's and have eth0 of the slave with the same IP address on it as eth0
of the master SER. The interfaces go through a switch that I can turn the
port off so there should be no conflict, but so far the improved routing of
Linux has foiled my strategy ie Linux provides a path through the working
interface, but I'm sure I'll find a way of isolating the interfaces, mucking
around with iptables and such. 

Do you know of anyone who has made this config work?
  
Thanks again for the help
Rick

-----Original Message-----
From: serusers-bounces at lists.iptel.org
[mailto:serusers-bounces at lists.iptel.org] On Behalf Of samuel
Sent: Thursday, July 27, 2006 3:59 AM
To: serusers at iptel.org
Subject: Re: FW: [Serusers] DNS SRV Mediaproxy

Can you get from the command line the SRV ressolution for mediaproy?
Try
#dig SRV _mediaproxy._tcp.mydomain.com
and check whether you get an answer...if not, there's some problem with DNS.
If you get the right answer, then probably the problem is in the SER
installation, remember to use mhomed=yes in the SER config file to
automatically select the right outbound socket (unless you want to do
it manually...)
I don't thing using two interfaces will affect directly how
proxydispatcher connects to DNS and ther resolved mediaproxies if *you
have the kernel routes properly configured*. Maybe you are trying to
contact a mediaproxy from an interface without connectivity to that
mediaproxy...

Hope it helps,
Samuel.

2006/7/26, Richard C. Thompson <rthompson at vir2com.com>:
>
>
>
>
> Thanks for the hints! Below is additional info in response.
>
> BTW the code for both the exit ser server and the new server are the same
> except for a few things like IP address and such.
>
>
> The new ser server has two interfaces and two IP addresses, does this mess
> things up?
>
>  ________________________________
>
>
>
>
>
> Without relevant parts of your config file it's hard to tell....it can be:
>
>  *you missed to include the new ser address in the allow statment of the
> existent mediaproxies
>
>
>
>
> I included the new ser IP address in the existing mediaproxies
>
>
> *there's an allow part in the DNS which does not include the new ser as
> allowed to query for the _mediaproxy._tcp
>
>
>
>
> I don't have an allow statement in the DNS Zone file. Is this what you are
> referring to?
>
> Does the new ser server have to be listed in the zone file?
>
>
> *the domain statement in the new ser's proxydispatcher is not properly set
>
>
> I have this in the mediaproxy.ini file
>
> defaultProxy = domain://mydomain.com
>
>
>  *a typo somewhere...
>
>
>
>
>   why doesn't this line in mediproxy.ini work either?
>
> defaultProxy =xx.xxx.xxx.xxx:25060 # IP address of one of the mediaproxy
> servers
>
>
>
>  few hints...
>  sAmuEl.
>
>
>
>
> 2006/7/26, Richard C. Thompson < rthompson at vir2com.com>:
>
>
>
>
> Hi
>
>
>
> Can anyone post a hint so I can figure this out.
>
>
>
> I have a ser server using a DNS lookup for my SRV mediaproxy servers.
> Everything works fine, and has been for some time.
>
> Now I built a new ser server and want to go to the same mediaproxy servers
> but I get the following error
>
>
>
> Jul 26 09:47:36 localhost proxydispatcher[31666]: warning: none of the
> proxies for domain mydomain.com have responded
>
> Jul 26 09:47:36 localhost proxydispatcher[31666]: error: No mediaproxy
> servers found for the default domain.
>
>
>
> I have included the new ser IP in the allow config of the mediaproxy
>
>
>
> Even if I force the defaultproxy to one of the IP addresses of a
mediaproxy
> server I get the following error
>
> error: couldn't forward command to 0.0.0.0:25060 (Connection reset by
peer)
>
>
>
> Any ideas???
>
> Could it be a version issue or maybe the python-mysqld issue, I'm not
using
> accounting.
>
>
>
>
>
>
>
> Rick
>
>
>
>
>
>
>
>
>  _______________________________________________
>  Serusers mailing list
>  Serusers at lists.iptel.org
>  http://lists.iptel.org/mailman/listinfo/serusers
>
>
>
>
>
> _______________________________________________
> Serusers mailing list
> Serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
>
>
>
_______________________________________________
Serusers mailing list
Serusers at lists.iptel.org
http://lists.iptel.org/mailman/listinfo/serusers