[Users] more on accounting

[tele]

Hi bogdan,

Unfortunaly the BYE come from my SoftSwitch is without route header.
I'm try to do something like that:

SS ------> OpenSER(acct) ----> OpenSER
    BYE         BYE               BYE
           OpenSER(acct) <----

maybe if the BYE come from another proxy it can recognize the ftag
paramater and do the correct accounting.

Or do have you others idea?


On Tue, 2006-07-11 at 09:30 +0300, Bogdan-Andrei Iancu wrote:
> Hi,
> 
> ftag is something specific to OpenSER/SER, there is no standard doc/spec 
> about it. The idea behind is to add the from tag to the Record-Route 
> header when the initial request passes. by comparing this value (the tag 
> of original from hdr) with the from tag of the sequential requests you 
> can figure out the direction of this request.
> 
> regards,
> bogdan
> 
> tele wrote:
> 
> >Hi,
> >
> >Can you point me to some documentation about the ftag parameter in the
> >RR/Route header?
> >I've search in the RFCs but not found any informations about.
> >
> >thank you
> >
> >On Mon, 2006-07-10 at 14:44 +0300, Bogdan-Andrei Iancu wrote:
> >  
> >
> >>Hi,
> >>
> >>in this case it means that the UA you were using was not correctly using 
> >>via the RR/Route headers and the RR header inserted by OpenSER was not 
> >>correctly mirrored into a Route hdr - this header is used to determine 
> >>the direction of the sequential requests.
> >>
> >>regards,
> >>bogdan
> >>
> >>tele wrote:
> >>
> >>    
> >>
> >>>Hi bogdan,
> >>>
> >>>now it works i can see the debug messages and OpenSER correctly swap
> >>>From/To for the accounting.
> >>>
> >>>But i didn't change the config, the only thing is that now signalling
> >>>message come from another proxy and not directly from UA.
> >>>
> >>>thank you for the support.
> >>>
> >>>On Mon, 2006-07-03 at 09:44 +0200, tele wrote:
> >>> 
> >>>
> >>>      
> >>>
> >>>>Hi Bogdan,
> >>>>
> >>>>I've updated to last CVS-head version. but in the log i can't see debug 
> >>>>messages.
> >>>>maybe there is an error in my accounting configuration. pls have a look:
> >>>>
> >>>>modparam("acc", "log_level", 2)
> >>>>modparam("acc", "log_fmt", "cdfimorstup")
> >>>>modparam("acc", "report_ack", 0)
> >>>>modparam("acc", "detect_direction", 1)
> >>>>modparam("acc", "radius_flag", 3)
> >>>>modparam("acc", "radius_missed_flag", 5)
> >>>>modparam("acc", "radius_config", 
> >>>>"/usr/local/etc/radiusclient-ng/radiusclient_auth.conf")
> >>>>modparam("acc", "radius_extra", "h323-setup-time=$avp(setup_time); 
> >>>>h323-connect-time=$avp(connect_time); 
> >>>>h323-disconnect-time=$avp(disconnect_time); 
> >>>>h323-remote-address=$avp(remote_address)")
> >>>>
> >>>>and before loose_route() i have:
> >>>>
> >>>>if (is_method("BYE"))
> >>>>{
> >>>>       setflag(3);
> >>>>       setflag(5);
> >>>>};
> >>>>
> >>>>is it correct?
> >>>>
> >>>>Bogdan-Andrei Iancu wrote:
> >>>>
> >>>>   
> >>>>
> >>>>        
> >>>>
> >>>>>Hi,
> >>>>>
> >>>>>as I saw in the log, the FROM restoring in BYE works properly, so 
> >>>>>RR/Route processing is fine. Are you sure you enabled the accounting 
> >>>>>for BYE?
> >>>>>
> >>>>>just in case, I added some more debug messages about this on cvs - 
> >>>>>please update and see the output. You should get:
> >>>>>  DBUG:acc:acc_onreq: UPSTREAM req detected -> flaging it
> >>>>>and
> >>>>>  DBUG:acc:fmt2strar: UPSTREAM flag set -> swap F/T
> >>>>>          
> >>>>>