[Serusers] Can't run SER with radius

[Roman]

Sorry forgot syslog messages:

Feb 17 16:37:41 uranus ser: ERROR: load_module: could not open module 
</usr/local/lib/ser/modules/auth_radius.so>: /usr/local/lib/ser/modules/auth_radius.so: 
undefined symbol: rc_dict_findvend
Feb 17 16:37:41 uranus ser: parse error (36,13-55): failed to load module
Feb 17 16:37:41 uranus ser: set_mod_param_regex: No module matching 
auth_radius found |
Feb 17 16:37:41 uranus ser: parse error (44,78-79): Can't set module parameter
Feb 17 16:37:41 uranus ser: set_mod_param_regex: No module matching 
auth_radius found |
Feb 17 16:37:41 uranus ser: parse error (45,43-44): Can't set module parameter
Feb 17 16:37:41 uranus ser: parse error (93,32-33): unknown command, missing 
loadmodule?


On Wednesday 16 February 2005 20:45, Roman wrote:
> Anybody please help with subj
> 0.8.14 binaries from iptel.org
> ser -dddddddd says:
> ERROR: bad config file (4 errors)
>
> config as in the manual:
>
> # ----------- global configuration parameters ------------------------
>
> debug=5         # debug level (cmd line: -dddddddddd)
> #fork=yes
> #log_stderror=no        # (cmd line: -E)
>
> /* Uncomment these lines to enter debugging mode
> debug=7
> fork=no
> log_stderror=yes
> */
>
> check_via=no    # (cmd. line: -v)
> dns=no           # (cmd. line: -r)
> rev_dns=no      # (cmd. line: -R)
> port=5065
> #children=4
> fifo="/tmp/ser_fifo"
>
> # ------------------ module loading ----------------------------------
>
> loadmodule "/usr/local/lib/ser/modules/sl.so"
> loadmodule "/usr/local/lib/ser/modules/tm.so"
> loadmodule "/usr/local/lib/ser/modules/rr.so"
> loadmodule "/usr/local/lib/ser/modules/maxfwd.so"
> loadmodule "/usr/local/lib/ser/modules/usrloc.so"
> loadmodule "/usr/local/lib/ser/modules/registrar.so"
>
> loadmodule "/usr/local/lib/ser/modules/auth.so"
> loadmodule "/usr/local/lib/ser/modules/auth_radius.so"
>
> # ----------------- setting module-specific parameters ---------------
>
> # -- usrloc params --
> modparam("usrloc", "db_mode", 2)
>
> # -- auth params --
> modparam("auth_radius",
> "radius_config","/etc/radiusclient/radiusclient.conf")
> modparam("auth_radius", "service_type", 15)
>
> # -- rr params --
> # add value to ;lr param to make some broken UAs happy
> modparam("rr", "enable_full_lr", 1)
>
> #modparam("acc", "log_level", 1)
> #modparam("acc", "radius_flag", 1)
>
> # -------------------------  request routing logic -------------------
> # main routing logic
>
>
> route{
>
>         # initial sanity checks -- messages with
>         # max_forwards==0, or excessively long requests
>         if (!mf_process_maxfwd_header("10")) {
>                 sl_send_reply("483","Too Many Hops");
>                 break;
>         };
>         if ( msg:len > max_len ) {
>                 sl_send_reply("513", "Message too big");
>                 break;
>         };
>
>         # we record-route all messages -- to make sure that
>         # subsequent messages will go through our proxy; that's
>         # particularly good if upstream and downstream entities
>         # use different transport protocol
>         record_route();
>         # loose-route processing
>         if (loose_route()) {
>                 t_relay();
>                 break;
>         };
>
>         # if the request is for other domain use UsrLoc
>         # (in case, it does not work, use the following command
>         # with proper names and addresses in it)
>         if (uri==myself) {
>
>                 if (method=="REGISTER") {
>
> # Uncomment this if you want to use digest authentication
>                         if (!radius_www_authorize("")) {
>                                 www_challenge("", "1");
>                                 break;
>                         };
>
>                         save("location");
>                         break;
>                 };
>
>                 # native SIP destinations are handled using our USRLOC DB
>                 if (!lookup("location")) {
>                         sl_send_reply("404", "Not Found");
>                         break;
>                 };
>         };
>         # forward to current uri now; use stateful forwarding; that
>         # works reliably even if we forward from TCP to UDP
>         if (!t_relay()) {
>                 sl_reply_error();
>         };
>
> }
>
> _______________________________________________
> Serusers mailing list
> serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers

-- 
Please avoid sending me Word or PowerPoint attachments.
See http://www.fsf.org/philosophy/no-word-attachments.html