[Serusers] Fwd: AS5300/E1 + SER -> PB : Cisco redirect calls on SER

[Alcée]

>
> Hello,
> I try to use cisco AS5300 with SER, like this  :
> 	phones -> SER -> AS5300 -> PSTN
> or
> 	phones -> AS5300 -> PSTN
> 				|
> 			         \/
> 			      SER
> But the second form does not work.
>
>
> I don't want people to directly ask for AS5300. So I follow the 
> "Howto" on SER web page.
> But nothing arrive on SER when I make a call directly to AS5300, The 
> call is forward to pstn.
> So I make this configuration to minimize the problem.
> But nothing at all.
> The "debug ccsip error" tells "no route to destination".
>
> Have you any idea ?
>
> thanks :)
>
> Alcée
>
> ! Last configuration change at 14:17:05 UTC Mon Apr 11 2005 by admin
> ! NVRAM config last updated at 12:57:01 UTC Mon Apr 11 2005 by admin
> !
> version 12.3
> service timestamps debug uptime
> service timestamps log uptime
> no service password-encryption
> !
> hostname VoIP
> !
> boot-start-marker
> boot-end-marker
> !
> !
> !
> resource-pool disable
> !
> aaa new-model
> !
> !
> aaa authentication login h323 group radius
> aaa authorization exec h323 group radius
> aaa accounting delay-start
> aaa accounting connection h323 start-stop group radius
> aaa nas port voip
> aaa session-id common
> ip subnet-zero
> !
> !
> isdn switch-type primary-net5
> !
> voice rtp send-recv
> voice echo-canceller extended
> !
> voice class codec 1
>  codec preference 1 g729r8 bytes 40
>  codec preference 2 g711ulaw
> !
> voice class codec 2
>  codec preference 1 g723ar63 bytes 48
>  codec preference 2 g723r63 bytes 48
>  codec preference 3 g729br8 bytes 40
>  codec preference 4 g729r8 bytes 40
>  codec preference 5 g723ar53 bytes 40
>  codec preference 6 g723r53 bytes 40
>  codec preference 7 g711ulaw
> !
> fax interface-type modem
> !
> !
> controller E1 0
>  clock source line primary
>  pri-group timeslots 1-31
> !
> controller E1 1
>  pri-group timeslots 1-31
> !
> controller E1 2
>  clock source line secondary 4
>  pri-group timeslots 1-31
> !
> controller E1 3
>  pri-group timeslots 1-31
> gw-accounting syslog
> gw-accounting aaa
>  attribute h323-remote-id resolved
>  acct-template callhistory-detail
>  suppress pots
> !
> !
> !
> interface Ethernet0
>  ip address 192.168.0.129 255.255.255.0
> !
> interface Serial0:15
>  no ip address
>  isdn switch-type primary-net5
>  isdn protocol-emulate network
>  no cdp enable
> !
> interface Serial1:15
>  no ip address
>  isdn switch-type primary-net5
>  no cdp enable
> !
> interface Serial2:15
>  no ip address
>  isdn switch-type primary-net5
>  no cdp enable
> !
> interface Serial3:15
>  no ip address
>  isdn switch-type primary-net5
>  no cdp enable
> !
> interface FastEthernet0
>  ip address 172.19.20.2 255.255.255.0
>  duplex full
>  speed 100
> !
> interface Dialer0
>  no ip address
> !
> ip classless
> ip route 0.0.0.0 0.0.0.0 172.19.20.1
> no ip http server
> !
> !
> logging facility local0
> logging 192.168.0.2
> !
> !
> radius-server host 192.168.0.2 auth-port 1812 acct-port 1813
> radius-server key test
> radius-server vsa send accounting
> radius-server vsa send authentication
> !
> voice-port 0:D
> !
> voice-port 1:D
> !
> voice-port 2:D
> !
> voice-port 3:D
> !
> !
> !
> dial-peer voice 3777 voip
>  huntstop
>  preference 2
>  application session
>  destination-pattern 3777#T
>  progress_ind setup enable 3
>  progress_ind alert enable 8
>  voice-class codec 2
>  session protocol sipv2
> session target sip-server
> dtmf-relay cisco-rtp h245-signal h245-alphanumeric
>  fax rate 9600
>  icpif 50
> !
> !
> sip-ua
>  retry invite 3
>  retry response 3
>  retry bye 3
>  retry cancel 3
>  timers expires 300000
>  timers connect 300
>  sip-server ipv4:192.168.0.1
> !
> !
> line con 0
> line aux 0
> line vty 0 4
>  password intermobile
> !
> ntp server 192.168.0.2
> end