[Serusers] Compile error on a V100

[Joseph Cheung]

Actually, I mean in the Makefile.defs; rather than using CFLAGS+= -mv8, I use CLFAGS+= -mpcu=ultrasparc

What I have found from the internet is that it is a problem in the 2.9x implementation of gcc. In short, the compiler generates v8plus instruction without telling the assembler and causing the problem below. By using the option as above, compiler and assembler does the job properly.

BTW, if you are using gcc 3.x, there is no issue as the Makefile.defs uses different CFLAGS.

Anyway, thanks for the response. 

-----Original Message-----
From: Andrei Pelinescu-Onciul [mailto:pelinescu-onciul at fokus.fraunhofer.de] 
Sent: June 25, 2004 4:38 AM
To: Joseph Cheung
Cc: serusers at lists.iptel.org
Subject: Re: [Serusers] Compile error on a V100

On Jun 24, 2004 at 18:48, Joseph Cheung <Joseph.Cheung2 at TELUS.COM> wrote:
> Solve the compilation problem finally by using -cpu=ultrasparc option.

What gcc version do you use?
I couldn't find ultrasparc in my gcc-2.95 man page.
I don't have gcc-2.95 installed any more on my ultrasparc (upgraded to
3.x) so I couldn't test it.

Andrei

> 
> -----Original Message-----
> From: serusers-bounces at iptel.org [mailto:serusers-bounces at lists.iptel.org] On Behalf Of Joseph Cheung
> Sent: June 24, 2004 5:23 PM
> To: serusers at lists.iptel.org
> Subject: [Serusers] Compile error on a V100
> 
> Hi.
> 
> I am trying to compile the SER on a Sun Fire V100 and have the following assemble error. 
> 
> I am wondering if someone could point me to the right direction.
> 
> Thanks
> 
> JC
> 
> bash: makeall: command not found
> ipvoiss1:/usr/joseph/JC/ser/ser-0.8.12$ make all
> Makefile.defs:473: Old gcc detected (2.9x), use  gcc >= 3.1 for better results
> Makefile:238: warning: overriding commands for target `/usr/local'
> Makefile:235: warning: ignoring old commands for target `/usr/local'
> Makefile:241: warning: overriding commands for target `/usr/local'
> Makefile:238: warning: ignoring old commands for target `/usr/local'
> Makefile:245: warning: overriding commands for target `/usr/local'
> Makefile:241: warning: ignoring old commands for target `/usr/local'
> Makefile:248: warning: overriding commands for target `/usr/local'
> Makefile:245: warning: ignoring old commands for target `/usr/local'
> Makefile:251: warning: overriding commands for target `/usr/local'
> Makefile:248: warning: ignoring old commands for target `/usr/local'
> gcc -g -O9 -funroll-loops   -Wall  -mv8      -DNAME='"ser"' -DVERSION='"0.8.12"' -DARCH='"sparc64"' -DOS='"solaris"' -DCOMPILER='"gcc 2.95"' -D__CPU_sparc64 -D__OS_solaris -DCFG_DIR='"/usr/local /etc/ser/"' -DPKG_MALLOC -DSHM_MEM  -DSHM_MMAP -DDNS_IP_HACK -DUSE_IPV6 -DUSE_TCP -DDISABLE_NAGLE
> -DF_MALLOC  -DFAST_LOCK -DADAPTIVE_WAIT -DADAPTIVE_WAIT_LOOPS=1024  -DHAVE_GETIPNODEBYNAME -DHAVE_SYS_SOCKIO_H -DHAVE_SCHED_YIELD -c main.c -o main.o
> /usr/ccs/bin/as: "/var/tmp/ccgv1YCz.s", line 1375: error: cannot use v8plus instructions in a non-v8plus target binary
> /usr/ccs/bin/as: "/var/tmp/ccgv1YCz.s", line 1401: error: cannot use v8plus instructions in a non-v8plus target binary
> /usr/ccs/bin/as: "/var/tmp/ccgv1YCz.s", line 10948: error: cannot use v8plus instructions in a non-v8plus target binary
> /usr/ccs/bin/as: "/var/tmp/ccgv1YCz.s", line 10977: error: cannot use v8plus instructions in a non-v8plus target binary
> make: *** [main.o] Error 1
> ipvoiss1:/usr/joseph/JC/ser/ser-0.8.12$
> 
> -----Original Message-----
> From: serusers-bounces at iptel.org [mailto:serusers-bounces at lists.iptel.org] On Behalf Of Jeremy George
> Sent: June 24, 2004 4:23 PM
> To: gc
> Cc: serusers at lists.iptel.org
> Subject: Re: [Serusers] Using AS5300 for SER
> 
> 
>   Where 10.1.1.1 is the address of the SER host and 10.2.1.1 is the
> address of the AS5300.
> 
> access-list 101 permit ip host 10.1.1.1 host 10.2.1.1
> access-list 101 deny   tcp any host 10.2.1.1 eq 5060
> access-list 101 deny   udp any host 10.2.1.1 eq 5060
> access-list 101 permit ip any any
> 
> - Jeremy
> 
> On Thu, 24 Jun 2004, gc wrote:
> 
> > Date: Thu, 24 Jun 2004 16:16:45 -0400
> > From: gc <garych at unidial.com>
> > To: serusers at lists.iptel.org
> > Subject: [Serusers] Using AS5300 for SER
> > 
> > I am using AS5300 as PSTN Gateway for SER. I'd like to make the AS5300 only accept sip call forward by ser. Does anybody know how to setup AS5300 for this?
> > 
> > Gary
> 
> -- 
> 
> _______________________________________________
> Serusers mailing list
> serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
> 
> 
> _______________________________________________
> Serusers mailing list
> serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
> 
> 
> _______________________________________________
> Serusers mailing list
> serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers