[Serusers] Sems Error

Ulrich Abend ullstar at iptel.org
Thu Apr 8 16:01:55 CEST 2004 

Please review the settings in your IP phone, the address settings in the SIP 
messages look a bit strange to me (IP, dest_IP...)

What are the IP addresses of you SIP phone and your server running ser&sems?

Regards,

Uli.


On Thursday 08 April 2004 15:46, Shirley wrote:
> Hi,
>
> Thank you for your reply. Now sems is running now...Thank you so much.
>
> When I try to do test call. It show "connected" on my UA but I hear no
> audio and the session ended. Please advice. Thanks again.
>  <<logNoAudio.txt>>
> Regards,
> Shirley
>
> > -----Original Message-----
> > From:	Ulrich Abend [SMTP:ullstar at iptel.org]
> > Sent:	Thursday, April 08, 2004 4:15 PM
> > To:	serusers at lists.iptel.org
> > Cc:	Shirley
> > Subject:	Re: [Serusers] Sems Error
> >
> > Hi,
> >
> > from your debugging:
> >
> > Apr  8 11:53:41 sipserver2 sems: (7785) DEBUG: loadAppPlugIn
> > (AmPlugIn.cpp:262): application 'number_reader' loaded.
> > Apr  8 11:53:41 sipserver2 sems: (7785) WARNING: reloadModuleConfig
> > (SemsConfiguration.cpp:66): no configuration found for module
> > number_reader,
> > maybe you want to specify config.number_reader in config file.
> > Apr  8 11:53:41 sipserver2 sems: (7785) ERROR: onLoad
> > (NumberReader.cpp:55):
> > required parameter number_path missing
> > Apr  8 11:53:41 sipserver2 sems: (7785) ERROR: load (AmPlugIn.cpp:85):
> > while
> > loading plug-in '/usr/local/lib/sems/plug-in/apps/number_reader.so'
> >
> > This says that number reader refuses to start and therefor SEMS refuses
> > to
> >
> > start at all. You have two options now:
> >
> > 1. configure number_reader to start by supplying valid entries in the
> > following new section of your sems.conf (edit wav to your valid path!):
> >
> > config.number_reader=inline
> > number_path=wav
> > prolog_file=wav/prolog.wav
> > epilog_file=wav/prolog.wav
> > config.number_reader=end
> >
> > 2. remove '/usr/local/lib/sems/plug-in/apps/number_reader.so', then sems
> > should start. Be careful, if you do a "make install" again, the module
> > will
> > be regenerated, you might have to delete it again.
> >
> >
> > I call this a bug in SEMS, we will fix it someday. Modules should start
> > without any configuration entries. By now, please use one of the options
> > above.
> >
> > > I have also tested this ps ax | grep sems. I get this result:~
> > > [root at sipserver2 root]# ps ax | grep sems
> > >  5518 ?        S      1:25 gedit file:///etc/sems/sems.conf
> > >  7805 pts/0    S      0:00 grep sems
> >
> > This shows, that no SEMS is running, from all processes containing "sems"
> > in
> > their command line, it's only your editor and the grep command itself.
> >
> > Please always view the output of SEMS startup and review all lines
> > starting
> > with ERROR.
> >
> > Regards,
> >
> > Uli.
> >
> > On Thursday 08 April 2004 06:05, Shirley wrote:
> > > Hi,
> > >
> > > Thank you for your prompt reply.
> > > I have  tested :~ set log_stderr=yes and fork=no and debug=3 in
> >
> > sems.conf.
> >
> > > I have attached the log. Please help.
> > >
> > >  <<SemsError1.txt>>  <<sems.conf>>
> > > I have also tested this ps ax | grep sems. I get this result:~
> > > [root at sipserver2 root]# ps ax | grep sems
> > >  5518 ?        S      1:25 gedit file:///etc/sems/sems.conf
> > >  7805 pts/0    S      0:00 grep sems
> > >
> > > Regards,
> > > Shirley
> > >
> > > > -----Original Message-----
> > > > From:	Ulrich Abend [SMTP:ullstar at iptel.org
> > > > Sent:	Thursday, April 08, 2004 12:18 AM
> > > > To:	Shirley
> > > > Cc:	serusers at lists.iptel.org
> > > > Subject:	Re: [Serusers] Sems Error
> > > >
> > > > Hi,
> > > >
> > > > try to set log_stderr=yes and fork=no and debug=3 in sems.conf for
> > > > testing, it
> > > > should produce a lot of debugging output on your console when
> > > > starting up.
> > > >
> > > > There are a lot of possible reasons for SEMS not starting, please
> > > > post the
> > > >
> > > > debugging output either from the commands above or from
> >
> > /var/log/syslog
> >
> > > > (under redhat the file might be another one under /var/log/ ...)
> > > >
> > > > You can also check is sems runs by calling in your shell:
> > > >
> > > >  ps ax | grep sems
> > > >
> > > > Regards,
> > > >
> > > > Uli.
> > > >
> > > > P.S.: Please always CC to the list, others might answer quicker than
> >
> > me
> >
> > > > :-)
> > > >
> > > > On Wednesday 07 April 2004 14:43, Shirley wrote:
> > > > > Hi,
> > > > >
> > > > > Thank you for your reply. How to make sure that the SEMS is
> > > > > running? I uses the /usr/local/sin/sems.redhat start- to start the
> > > > > sems
> >
> > service?
> >
> > > > Am
> > > >
> > > > > I correct?
> > > > > My fifo name is same in both file that you mention. Please advice!
> > > >
> > > > Thanks
> > > >
> > > > > Regards,
> > > > > Shirley
> > > > >
> > > > > > -----Original Message-----
> > > > > > From:	Ulrich Abend [SMTP:ullstar at iptel.org]
> > > > > > Sent:	Wednesday, April 07, 2004 8:00 PM
> > > > > > To:	serusers at lists.iptel.org
> > > > > > Cc:	Shirley
> > > > > > Subject:	Re: [Serusers] Sems Error
> > > > > >
> > > > > > Hi,
> > > > > >
> > > > > > you should make shure, SEMS is running and uses the same fifo
> > > > > > name (in sems.conf) as SER (in ser.cfg).
> > > > > >
> > > > > > It is also important, that the fifo file (default: /tmp/am_fifo)
> >
> > has
> >
> > > > > > write
> > > > > >
> > > > > > permissions for the user SER runs as. The easiest setup is to run
> >
> > SER
> >
> > > > and
> > > >
> > > > > > SEMS as the same user.
> > > > > >
> > > > > > If you still experience problems, please post SER and SEMS
> >
> > debugging
> >
> > > > > > output,
> > > > > > the config files, and the results of
> > > > > > ls -la /tmp/*fifo
> > > > > >
> > > > > > Regards,
> > > > > >
> > > > > > Uli.
> > > > > >
> > > > > > On Wednesday 07 April 2004 12:28, Shirley wrote:
> > > > > > > Hi all,
> > > > > > >
> > > > > > > Please Help!!! I am trying to install the sems when I try to
> >
> > start
> >
> > > > the
> > > >
> > > > > > sems
> > > > > >
> > > > > > > I encountered this problem as per below. I am running on Linux
> >
> > 9.0
> >
> > > > and
> > > >
> > > > > > > please also advice on how to check the fifo version....Thanks
> > > > > > >
> > > > > > > Mar 24 19:04:25 sipserver2 /usr/local/sbin/ser[12876]: ERROR:
> > > > > > > voicemail: ans_machine deamon is not running !
> > > > > > > Mar 24 19:04:25 sipserver2 /usr/local/sbin/ser[12876]: ERROR:
> > > > > > > voicemail:
> > > > > >
> > > > > > No
> > > > > >
> > > > > > > such device or address
> > > > > > > Mar 24 19:04:25 sipserver2 /usr/local/sbin/ser[12876]: ERROR:
> > > >
> > > > vm_start:
> > > > > > > write_to_fifo failed
> > > > > > > Mar 24 19:04:35 sipserver2 /usr/local/sbin/ser[12874]: ERROR:
> > > > > > > voicemail: ans_machine deamon is not running !
> > > > > > > Mar 24 19:04:35 sipserver2 /usr/local/sbin/ser[12874]: ERROR:
> > > > > > > voicemail:
> > > > > >
> > > > > > No
> > > > > >
> > > > > > > such device or address
> > > > > > > Mar 24 19:04:35 sipserver2 /usr/local/sbin/ser[12874]: ERROR:
> > > >
> > > > vm_start:
> > > > > > > write_to_fifo failed
> > > > > > >
> > > > > > > regards,
> > > > > > > shirley
> > > > > > >
> > > > > > > _______________________________________________
> > > > > > > Serusers mailing list
> > > > > > > serusers at lists.iptel.org
> > > > > > > http://lists.iptel.org/mailman/listinfo/serusers

More information about the sr-users mailing list