[SR-Users] IPv4, IPv6, RTPProxy and Kamailio
Mark Zeman
mark.zeman at students.fhnw.ch
Tue Dec 3 17:17:16 CET 2013
The SIP packets are fine - we are able to establish SIP session with a
secured control channel as easily as with an unsecured one.
As long as the RTPProxy doesn't get involved (i.e. as long as it's
IPvX-IPvX and not IPv4-IPv6) everything works!
With the RTPProxy, the connection gets established (SIP still works)
but RTP only comes from one side, the caller, and even that is not
relayed.
It appears that Kamailio doesn't even enter the route[IPV4V6] part of
its config, for example...
I will be able to send logs tomorrow, but I can show you our config, if
that might help.
On Tue 03 Dec 2013 03:27:55 PM CET, Klaus Darilion wrote:
> On 03.12.2013 14:23, Mark Zeman wrote:
>> Hello all,
>>
>> The subject says most of it, I think.
>>
>> We set up our Kamailio and RTPProxy according to
>> http://kb.asipto.com/kamailio:kamailio-mixed-ipv4-ipv6
>> with the addition of an alias (siplab.ch), and the DNS to go with it, as
>> well as TLS and SRTP.
>>
>> However, we only get working calls IPv4-IPv4 and IPv6-IPv6! IPv4-IPv6 we
>> get a proper connection,
>> secured with SRTP, but no audio. Looking at the network, RTP packets go
>> from the caller to the server,
>> but nothing leaves the server and no RTP packets go from callee to
>> server.
>>
>> Do you have any idea how to fix this?
>
> Before fixing you need to find the problem. Probably the SDP get
> rewritten incorrect. To debug this issue, you have to inspect the ip
> address and ports in the received and sent SDPs if they are correct
> (e.g. IPv4 and IPv6 address of the rtpproxy).
>
> You mentioned TLS - thus it is difficult to inspect the raw SIP
> packets. Is such cases you can either:
> - adding lots of xlog("$mb, ...") to your config and watch syslog
> - use the sipcapture module to write every incoming and outgoing SIP
> message to the DB, and analyze the packets in the DB
> - Disable TLS. Use TCP. If it fails with TCP it will also fail with
> TLS. Once it works over TCP, it will also work over TLS.
> - If you really have a problem with TLS only, you could enable the
> NULL cipher to have a unencrypted TLS connection, or use Wireshark's
> TLS decoding capabilities
> - Configure rtpproxy to communicate via UDP socket instead TCP socket.
> Then you can also capture the communication between Kamailio and
> rtpproxy.
>
> It seems you just call the rtpproxy functions with some wrong flags.
> Make sure properly detect the direction (4to6 or 6to4) an set the i
> and e flags accordingly.
>
> regards
> Klaus
-------------- next part --------------
#!KAMAILIO
#
# Kamailio (OpenSER) SIP Server v4.0 - default configuration script
# - web: http://www.kamailio.org
# - git: http://sip-router.org
#
# Direct your questions about this file to: <sr-users at lists.sip-router.org>
#
# Refer to the Core CookBook at http://www.kamailio.org/wiki/
# for an explanation of possible statements, functions and parameters.
#
# Several features can be enabled using '#!define WITH_FEATURE' directives:
#
# *** To run in debug mode:
# - define WITH_DEBUG
#
# *** To enable mysql:
# - define WITH_MYSQL
#
# *** To enable authentication execute:
# - enable mysql
# - define WITH_AUTH
# - add users using 'kamctl'
#
# *** To enable IP authentication execute:
# - enable mysql
# - enable authentication
# - define WITH_IPAUTH
# - add IP addresses with group id '1' to 'address' table
#
# *** To enable persistent user location execute:
# - enable mysql
# - define WITH_USRLOCDB
#
# *** To enable presence server execute:
# - enable mysql
# - define WITH_PRESENCE
#
# *** To enable nat traversal execute:
# - define WITH_NAT
# - install RTPProxy: http://www.rtpproxy.org
# - start RTPProxy:
# rtpproxy -l _your_public_ip_ -s udp:localhost:7722
#
# *** To enable PSTN gateway routing execute:
# - define WITH_PSTN
# - set the value of pstn.gw_ip
# - check route[PSTN] for regexp routing condition
#
# *** To enable database aliases lookup execute:
# - enable mysql
# - define WITH_ALIASDB
#
# *** To enable speed dial lookup execute:
# - enable mysql
# - define WITH_SPEEDDIAL
#
# *** To enable multi-domain support execute:
# - enable mysql
# - define WITH_MULTIDOMAIN
#
# *** To enable TLS support execute:
# - adjust CFGDIR/tls.cfg as needed
# - define WITH_TLS
#
# *** To enable XMLRPC support execute:
# - define WITH_XMLRPC
# - adjust route[XMLRPC] for access policy
#
# *** To enable anti-flood detection execute:
# - adjust pike and htable=>ipban settings as needed (default is
# block if more than 16 requests in 2 seconds and ban for 300 seconds)
# - define WITH_ANTIFLOOD
#
# *** To block 3XX redirect replies execute:
# - define WITH_BLOCK3XX
#
# *** To enable VoiceMail routing execute:
# - define WITH_VOICEMAIL
# - set the value of voicemail.srv_ip
# - adjust the value of voicemail.srv_port
#
# *** To enhance accounting execute:
# - enable mysql
# - define WITH_ACCDB
# - add following columns to database
#!ifdef ACCDB_COMMENT
ALTER TABLE acc ADD COLUMN src_user VARCHAR(64) NOT NULL DEFAULT '';
ALTER TABLE acc ADD COLUMN src_domain VARCHAR(128) NOT NULL DEFAULT '';
ALTER TABLE acc ADD COLUMN src_ip varchar(64) NOT NULL default '';
ALTER TABLE acc ADD COLUMN dst_ouser VARCHAR(64) NOT NULL DEFAULT '';
ALTER TABLE acc ADD COLUMN dst_user VARCHAR(64) NOT NULL DEFAULT '';
ALTER TABLE acc ADD COLUMN dst_domain VARCHAR(128) NOT NULL DEFAULT '';
ALTER TABLE missed_calls ADD COLUMN src_user VARCHAR(64) NOT NULL DEFAULT '';
ALTER TABLE missed_calls ADD COLUMN src_domain VARCHAR(128) NOT NULL DEFAULT '';
ALTER TABLE missed_calls ADD COLUMN src_ip varchar(64) NOT NULL default '';
ALTER TABLE missed_calls ADD COLUMN dst_ouser VARCHAR(64) NOT NULL DEFAULT '';
ALTER TABLE missed_calls ADD COLUMN dst_user VARCHAR(64) NOT NULL DEFAULT '';
ALTER TABLE missed_calls ADD COLUMN dst_domain VARCHAR(128) NOT NULL DEFAULT '';
#!endif
####### Include Local Config If Exists #########
import_file "kamailio-local.cfg"
####### Defined Values #########
#!define WITH_MYSQL
#!define WITH_AUTH
#!define WITH_USRLOCDB
#!define WITH_DEBUG
#!define WITH_NAT
#!define WITH_IPV6
#!define WITH_TLS
#!define ADDR_IPV4 192.168.1.11
#!define ADDR_IPV6 [2002:c0a8:101::11]
# *** Value defines - IDs used later in config
#!ifdef WITH_MYSQL
# - database URL - used to connect to database server by modules such
# as: auth_db, acc, usrloc, a.s.o.
#!ifndef DBURL
#!define DBURL "mysql://kamailio:clangsip@localhost/db_siplab"
#!endif
#!endif
#!ifdef WITH_MULTIDOMAIN
# - the value for 'use_domain' parameters
#!define MULTIDOMAIN 1
#!else
#!define MULTIDOMAIN 0
#!endif
# - flags
# FLT_ - per transaction (message) flags
# FLB_ - per branch flags
#!define FLT_ACC 1
#!define FLT_ACCMISSED 2
#!define FLT_ACCFAILED 3
#!define FLT_NATS 5
#!define FLB_NATB 1
#!define FLB_NATSIPPING 2
#!define FLB_IPV6 6
#!define FLB_V4V6 7
####### Global Parameters #########
### LOG Levels: 3=DBG, 2=INFO, 1=NOTICE, 0=WARN, -1=ERR
#!ifdef WITH_DEBUG
debug=4
log_stderror=yes
#!else
debug=2
log_stderror=no
#!endif
memdbg=5
memlog=5
log_facility=LOG_LOCAL0
fork=yes
children=4
/* uncomment the next line to disable TCP (default on) */
#disable_tcp=yes
/* uncomment the next line to disable the auto discovery of local aliases
based on reverse DNS on IPs (default on) */
#auto_aliases=no
/* add local domain aliases */
alias="siplab.ch"
alias="proxy.siplab.ch"
alias="proxyv4.siplab.ch"
alias="proxyv6.siplab.ch"
/* uncomment and configure the following line if you want Kamailio to
bind on a specific interface/port/proto (default bind on all available) */
/*
listen=udp:192.168.1.11:5060
listen=tcp:192.168.1.11:5060
listen=tls:192.168.1.11:5061
listen=udp:[2002:c0a8:101::11]:5060
listen=tcp:[2002:c0a8:101::11]:5060
listen=tls:[2002:c0a8:101::11]:5061
*/
listen=ADDR_IPV4
listen=ADDR_IPV6
/* port to listen to
* - can be specified more than once if needed to listen on many ports */
port=5060
#!ifdef WITH_TLS
enable_tls=yes
#!endif
# life time of TCP connection when there is no traffic
# - a bit higher than registration expires to cope with UA behind NAT
tcp_connection_lifetime=3605
####### Custom Parameters #########
# These parameters can be modified runtime via RPC interface
# - see the documentation of 'cfg_rpc' module.
#
# Format: group.id = value 'desc' description
# Access: $sel(cfg_get.group.id) or @cfg_get.group.id
#
#!ifdef WITH_PSTN
# PSTN GW Routing
#
# - pstn.gw_ip: valid IP or hostname as string value, example:
# pstn.gw_ip = "10.0.0.101" desc "My PSTN GW Address"
#
# - by default is empty to avoid misrouting
pstn.gw_ip = "" desc "PSTN GW Address"
pstn.gw_port = "" desc "PSTN GW Port"
#!endif
#!ifdef WITH_VOICEMAIL
# VoiceMail Routing on offline, busy or no answer
#
# - by default Voicemail server IP is empty to avoid misrouting
voicemail.srv_ip = "" desc "VoiceMail IP Address"
voicemail.srv_port = "5060" desc "VoiceMail Port"
#!endif
####### Modules Section ########
# set paths to location of modules (to sources or installation folders)
#!ifdef WITH_SRCPATH
mpath="modules_k:modules"
#!else
mpath="/usr/lib64/kamailio/modules/"
#!endif
#!ifdef WITH_MYSQL
loadmodule "db_mysql.so"
#!endif
loadmodule "mi_fifo.so"
loadmodule "kex.so"
loadmodule "corex.so"
loadmodule "tm.so"
loadmodule "tmx.so"
loadmodule "sl.so"
loadmodule "rr.so"
loadmodule "pv.so"
loadmodule "maxfwd.so"
loadmodule "usrloc.so"
loadmodule "registrar.so"
loadmodule "textops.so"
loadmodule "siputils.so"
loadmodule "xlog.so"
loadmodule "sanity.so"
loadmodule "ctl.so"
loadmodule "cfg_rpc.so"
loadmodule "mi_rpc.so"
loadmodule "acc.so"
#!ifdef WITH_AUTH
loadmodule "auth.so"
loadmodule "auth_db.so"
#!ifdef WITH_IPAUTH
loadmodule "permissions.so"
#!endif
#!endif
#!ifdef WITH_ALIASDB
loadmodule "alias_db.so"
#!endif
#!ifdef WITH_SPEEDDIAL
loadmodule "speeddial.so"
#!endif
#!ifdef WITH_MULTIDOMAIN
loadmodule "domain.so"
#!endif
#!ifdef WITH_PRESENCE
loadmodule "presence.so"
loadmodule "presence_xml.so"
#!endif
#!ifdef WITH_NAT
loadmodule "nathelper.so"
xdbg("LOADING RTPPROXY");
loadmodule "rtpproxy.so"
xdbg("LOADED RTPPROXY");
#!endif
#!ifdef WITH_TLS
loadmodule "tls.so"
#!endif
#!ifdef WITH_ANTIFLOOD
loadmodule "htable.so"
loadmodule "pike.so"
#!endif
#!ifdef WITH_XMLRPC
loadmodule "xmlrpc.so"
#!endif
#!ifdef WITH_DEBUG
loadmodule "debugger.so"
#!endif
# ----------------- setting module-specific parameters ---------------
# ----- mi_fifo params -----
modparam("mi_fifo", "fifo_name", "/tmp/kamailio_fifo")
# ----- tm params -----
# auto-discard branches from previous serial forking leg
modparam("tm", "failure_reply_mode", 3)
# default retransmission timeout: 30sec
modparam("tm", "fr_timer", 30000)
# default invite retransmission timeout after 1xx: 120sec
modparam("tm", "fr_inv_timer", 120000)
# ----- rr params -----
# add value to ;lr param to cope with most of the UAs
modparam("rr", "enable_full_lr", 1)
# do not append from tag to the RR (no need for this script)
modparam("rr", "append_fromtag", 0)
# ----- registrar params -----
modparam("registrar", "method_filtering", 1)
/* uncomment the next line to disable parallel forking via location */
# modparam("registrar", "append_branches", 0)
/* uncomment the next line not to allow more than 10 contacts per AOR */
modparam("registrar", "max_contacts", 2)
# max value for expires of registrations
modparam("registrar", "max_expires", 3600)
# set it to 1 to enable GRUU
modparam("registrar", "gruu_enabled", 0)
# ----- acc params -----
/* what special events should be accounted ? */
modparam("acc", "early_media", 0)
modparam("acc", "report_ack", 0)
modparam("acc", "report_cancels", 0)
/* by default ww do not adjust the direct of the sequential requests.
if you enable this parameter, be sure the enable "append_fromtag"
in "rr" module */
modparam("acc", "detect_direction", 0)
/* account triggers (flags) */
modparam("acc", "log_flag", FLT_ACC)
modparam("acc", "log_missed_flag", FLT_ACCMISSED)
modparam("acc", "log_extra",
"src_user=$fU;src_domain=$fd;src_ip=$si;"
"dst_ouser=$tU;dst_user=$rU;dst_domain=$rd")
modparam("acc", "failed_transaction_flag", FLT_ACCFAILED)
/* enhanced DB accounting */
#!ifdef WITH_ACCDB
modparam("acc", "db_flag", FLT_ACC)
modparam("acc", "db_missed_flag", FLT_ACCMISSED)
modparam("acc", "db_url", DBURL)
modparam("acc", "db_extra",
"src_user=$fU;src_domain=$fd;src_ip=$si;"
"dst_ouser=$tU;dst_user=$rU;dst_domain=$rd")
#!endif
# ----- usrloc params -----
/* enable DB persistency for location entries */
#!ifdef WITH_USRLOCDB
modparam("usrloc", "db_url", DBURL)
modparam("usrloc", "db_mode", 2)
modparam("usrloc", "use_domain", MULTIDOMAIN)
#!endif
# ----- auth_db params -----
#!ifdef WITH_AUTH
modparam("auth_db", "db_url", DBURL)
modparam("auth_db", "calculate_ha1", yes)
modparam("auth_db", "password_column", "password")
modparam("auth_db", "load_credentials", "")
modparam("auth_db", "use_domain", MULTIDOMAIN)
# ----- permissions params -----
#!ifdef WITH_IPAUTH
modparam("permissions", "db_url", DBURL)
modparam("permissions", "db_mode", 1)
#!endif
#!endif
# ----- alias_db params -----
#!ifdef WITH_ALIASDB
modparam("alias_db", "db_url", DBURL)
modparam("alias_db", "use_domain", MULTIDOMAIN)
#!endif
# ----- speeddial params -----
#!ifdef WITH_SPEEDDIAL
modparam("speeddial", "db_url", DBURL)
modparam("speeddial", "use_domain", MULTIDOMAIN)
#!endif
# ----- domain params -----
#!ifdef WITH_MULTIDOMAIN
modparam("domain", "db_url", DBURL)
# register callback to match myself condition with domains list
modparam("domain", "register_myself", 1)
#!endif
#!ifdef WITH_PRESENCE
# ----- presence params -----
modparam("presence", "db_url", DBURL)
# ----- presence_xml params -----
modparam("presence_xml", "db_url", DBURL)
modparam("presence_xml", "force_active", 1)
#!endif
#!ifdef WITH_NAT
# ----- rtpproxy params -----
modparam("rtpproxy", "rtpproxy_sock", "unix:/var/run/rtpproxy/rtpproxy.sock")
# ----- nathelper params -----
modparam("nathelper", "natping_interval", 30)
modparam("nathelper", "ping_nated_only", 1)
modparam("nathelper", "sipping_bflag", FLB_NATSIPPING)
modparam("nathelper", "sipping_from", "sip:pinger at siplab.ch")
# params needed for NAT traversal in other modules
modparam("nathelper|registrar", "received_avp", "$avp(RECEIVED)")
modparam("usrloc", "nat_bflag", FLB_NATB)
#!endif
#!ifdef WITH_TLS
# ----- tls params -----
modparam("tls", "config", "/etc/kamailio/tls.cfg")
#!endif
#!ifdef WITH_ANTIFLOOD
# ----- pike params -----
modparam("pike", "sampling_time_unit", 2)
modparam("pike", "reqs_density_per_unit", 16)
modparam("pike", "remove_latency", 4)
# ----- htable params -----
# ip ban htable with autoexpire after 5 minutes
modparam("htable", "htable", "ipban=>size=8;autoexpire=300;")
#!endif
#!ifdef WITH_XMLRPC
# ----- xmlrpc params -----
modparam("xmlrpc", "route", "XMLRPC");
modparam("xmlrpc", "url_match", "^/RPC")
#!endif
#!ifdef WITH_DEBUG
# ----- debugger params -----
modparam("debugger", "cfgtrace", 1)
#!endif
####### Routing Logic ########
# Main SIP request routing logic
# - processing of any incoming SIP request starts with this route
# - note: this is the same as route { ... }
request_route {
# per request initial checks
route(REQINIT);
# NAT detection
route(NATDETECT);
# CANCEL processing
if (is_method("CANCEL"))
{
if (t_check_trans()) {
route(RELAY);
}
exit;
}
# handle requests within SIP dialogs
route(WITHINDLG);
### only initial requests (no To tag)
t_check_trans();
# authentication
route(AUTH);
# record routing for dialog forming requests (in case they are routed)
# - remove preloaded route headers
remove_hf("Route");
if (is_method("INVITE|SUBSCRIBE"))
record_route();
# account only INVITEs
if (is_method("INVITE"))
{
setflag(FLT_ACC); # do accounting
}
# dispatch requests to foreign domains
route(SIPOUT);
### requests for my local domains
# handle presence related requests
route(PRESENCE);
# handle registrations
route(REGISTRAR);
if ($rU==$null)
{
# request with no Username in RURI
sl_send_reply("484","Address Incomplete");
exit;
}
# dispatch destinations to PSTN
route(PSTN);
# user location service
route(LOCATION);
route(RELAY);
}
route[RELAY] {
# enable additional event routes for forwarded requests
# - serial forking, RTP relaying handling, a.s.o.
if (is_method("INVITE|SUBSCRIBE")) {
t_on_branch("MANAGE_BRANCH");
t_on_reply("MANAGE_REPLY");
}
if (is_method("INVITE")) {
t_on_failure("MANAGE_FAILURE");
}
if (!t_relay()) {
sl_reply_error();
}
exit;
}
# Per SIP request initial checks
route[REQINIT] {
#!ifdef WITH_ANTIFLOOD
# flood dection from same IP and traffic ban for a while
# be sure you exclude checking trusted peers, such as pstn gateways
# - local host excluded (e.g., loop to self)
if(src_ip!=myself)
{
if($sht(ipban=>$si)!=$null)
{
# ip is already blocked
xdbg("request from blocked IP - $rm from $fu (IP:$si:$sp)\n");
exit;
}
if (!pike_check_req())
{
xlog("L_ALERT","ALERT: pike blocking $rm from $fu (IP:$si:$sp)\n");
$sht(ipban=>$si) = 1;
exit;
}
}
#!endif
if (!mf_process_maxfwd_header("10")) {
sl_send_reply("483","Too Many Hops");
exit;
}
if(!sanity_check("1511", "7"))
{
xlog("Malformed SIP message from $si:$sp\n");
exit;
}
}
# Handle requests within SIP dialogs
route[WITHINDLG] {
if (has_totag()) {
# sequential request withing a dialog should
# take the path determined by record-routing
if (loose_route()) {
route(DLGURI);
if (is_method("BYE")) {
setflag(FLT_ACC); # do accounting ...
setflag(FLT_ACCFAILED); # ... even if the transaction fails
}
else if ( is_method("ACK") ) {
# ACK is forwarded statelessy
route(NATMANAGE);
}
else if ( is_method("NOTIFY") ) {
# Add Record-Route for in-dialog NOTIFY as per RFC 6665.
record_route();
}
route(RELAY);
} else {
if (is_method("SUBSCRIBE") && uri == myself) {
# in-dialog subscribe requests
route(PRESENCE);
exit;
}
if ( is_method("ACK") ) {
if ( t_check_trans() ) {
# no loose-route, but stateful ACK;
# must be an ACK after a 487
# or e.g. 404 from upstream server
route(RELAY);
exit;
} else {
# ACK without matching transaction ... ignore and discard
exit;
}
}
sl_send_reply("404","Not here");
}
exit;
}
}
# Handle SIP registrations
route[REGISTRAR] {
if (is_method("REGISTER"))
{
if(isflagset(FLT_NATS))
{
setbflag(FLB_NATB);
# uncomment next line to do SIP NAT pinging
setbflag(FLB_NATSIPPING);
}
if(af==INET6)
setbflag(FLB_IPV6);
if (!save("location"))
sl_reply_error();
exit;
}
}
# USER location service
route[LOCATION] {
#!ifdef WITH_SPEEDDIAL
# search for short dialing - 2-digit extension
if($rU=~"^[0-9][0-9]$")
if(sd_lookup("speed_dial"))
route(SIPOUT);
#!endif
#!ifdef WITH_ALIASDB
# search in DB-based aliases
if(alias_db_lookup("dbaliases"))
route(SIPOUT);
#!endif
$avp(oexten) = $rU;
if (!lookup("location")) {
$var(rc) = $rc;
route(TOVOICEMAIL);
t_newtran();
switch ($var(rc)) {
case -1:
case -3:
send_reply("404", "Not Found");
exit;
case -2:
send_reply("405", "Method Not Allowed");
exit;
}
}
# when routing via usrloc, log the missed calls also
if (is_method("INVITE"))
{
setflag(FLT_ACCMISSED);
}
route(RELAY);
exit;
}
# Presence server route
route[PRESENCE] {
if(!is_method("PUBLISH|SUBSCRIBE"))
return;
#!ifdef WITH_PRESENCE
if (!t_newtran())
{
sl_reply_error();
exit;
};
if(is_method("PUBLISH"))
{
handle_publish();
t_release();
}
else
if( is_method("SUBSCRIBE"))
{
handle_subscribe();
t_release();
}
exit;
#!endif
# if presence enabled, this part will not be executed
if (is_method("PUBLISH") || $rU==$null)
{
sl_send_reply("404", "Not here");
exit;
}
return;
}
# Authentication route
route[AUTH] {
#!ifdef WITH_AUTH
#!ifdef WITH_IPAUTH
if((!is_method("REGISTER")) && allow_source_address())
{
# source IP allowed
return;
}
#!endif
if (is_method("REGISTER") || from_uri==myself)
{
# authenticate requests
if (!auth_check("$fd", "subscriber", "1")) {
auth_challenge("$fd", "0");
exit;
}
# user authenticated - remove auth header
if(!is_method("REGISTER|PUBLISH"))
consume_credentials();
}
# if caller is not local subscriber, then check if it calls
# a local destination, otherwise deny, not an open relay here
if (from_uri!=myself && uri!=myself)
{
sl_send_reply("403","Not relaying");
exit;
}
#!endif
return;
}
# Caller NAT detection route
route[NATDETECT] {
if(af==INET6)
return;
#!ifdef WITH_NAT
force_rport();
if (nat_uac_test("19")) {
if (is_method("REGISTER")) {
fix_nated_register();
} else {
add_contact_alias();
}
setflag(FLT_NATS);
}
#!endif
return;
}
# RTPProxy control
route[NATMANAGE] {
#!ifdef WITH_NAT
if (is_request()) {
if(has_totag()) {
if(check_route_param("nat=yes")) {
setbflag(FLB_NATB);
} else {
if(check_route_param("nat=v46")) {
setbflag(FLB_V4V6);
}
}
}
}
if (!(isflagset(FLT_NATS) || isbflagset(FLB_NATB) || isbflagset(FLB_V4V6)))
return;
if(isflagset(FLB_V4V6)) {
if(af==INET6) {
xdbg("ZEMAN: FAEI");
rtpproxy_manage("FAEI");
} else {
xdbg("ZEMAN: FAIE");
rtpproxy_manage("FAIE");
}
} else {
if(af==INET6) {
xdbg("ZEMAN: FAEE");
rtpproxy_manage("FAEE");
} else {
xdbg("ZEMAN: FAII");
rtpproxy_manage("FAII");
}
}
if (is_request()) {
if (!has_totag()) {
if (isbflagset(FLB_V4V6)) {
add_rr_param(";nat=v46");
} else {
add_rr_param(";nat=yes");
}
}
}
if (is_reply()) {
if(isbflagset(FLB_NATB)) {
if(af==INET) {
fix_nated_contact();
}
}
}
#!endif
return;
}
# URI update for dialog requests
route[DLGURI] {
#!ifdef WITH_NAT
if(!isdsturiset()) {
handle_ruri_alias();
}
#!endif
return;
}
# Routing to foreign domains
route[SIPOUT] {
if (!uri==myself)
{
append_hf("P-hint: outbound\r\n");
route(RELAY);
}
}
# PSTN GW routing
route[PSTN] {
#!ifdef WITH_PSTN
# check if PSTN GW IP is defined
if (strempty($sel(cfg_get.pstn.gw_ip))) {
xlog("SCRIPT: PSTN rotuing enabled but pstn.gw_ip not defined\n");
return;
}
# route to PSTN dialed numbers starting with '+' or '00'
# (international format)
# - update the condition to match your dialing rules for PSTN routing
if(!($rU=~"^(\+|00)[1-9][0-9]{3,20}$"))
return;
# only local users allowed to call
if(from_uri!=myself) {
sl_send_reply("403", "Not Allowed");
exit;
}
if (strempty($sel(cfg_get.pstn.gw_port))) {
$ru = "sip:" + $rU + "@" + $sel(cfg_get.pstn.gw_ip);
} else {
$ru = "sip:" + $rU + "@" + $sel(cfg_get.pstn.gw_ip) + ":"
+ $sel(cfg_get.pstn.gw_port);
}
route(RELAY);
exit;
#!endif
return;
}
# XMLRPC routing
#!ifdef WITH_XMLRPC
route[XMLRPC] {
# allow XMLRPC from localhost
if ((method=="POST" || method=="GET")
&& (src_ip==127.0.0.1)) {
# close connection only for xmlrpclib user agents (there is a bug in
# xmlrpclib: it waits for EOF before interpreting the response).
if ($hdr(User-Agent) =~ "xmlrpclib")
set_reply_close();
set_reply_no_connect();
dispatch_rpc();
exit;
}
send_reply("403", "Forbidden");
exit;
}
#!endif
# route to voicemail server
route[TOVOICEMAIL] {
#!ifdef WITH_VOICEMAIL
if(!is_method("INVITE"))
return;
# check if VoiceMail server IP is defined
if (strempty($sel(cfg_get.voicemail.srv_ip))) {
xlog("SCRIPT: VoiceMail rotuing enabled but IP not defined\n");
return;
}
if($avp(oexten)==$null)
return;
$ru = "sip:" + $avp(oexten) + "@" + $sel(cfg_get.voicemail.srv_ip)
+ ":" + $sel(cfg_get.voicemail.srv_port);
route(RELAY);
exit;
#!endif
return;
}
# detect if IPv4 - IPv6 bridging is needed
route[IPV4V6] {
xdbg("ZEMAN: HAS TO TAG?");
if(!has_totag()) {
if(af==INET6 && !isbflagset(FLB_IPV6)) {
xdbg("ZEMAN: IPV4V6 FLB SET");
setbflag(FLB_V4V6);
} else {
if(af==INET && isbflagset(FLB_IPV6)) {
setbflag(FLB_V4V6);
}
}
return;
}
}
# manage outgoing branches
branch_route[MANAGE_BRANCH] {
xdbg("new branch [$T_branch_idx] to $ru\n");
route(IPV4V6);
route(NATMANAGE);
}
# manage incoming replies
onreply_route[MANAGE_REPLY] {
xdbg("incoming reply\n");
if(status=~"[12][0-9][0-9]") {
/*if(isbflagset(FLB_V4V6)){
route(IPV4V6);
}*/
route(NATMANAGE);
}
}
# manage failure routing cases
failure_route[MANAGE_FAILURE] {
route(NATMANAGE);
if (t_is_canceled()) {
exit;
}
#!ifdef WITH_BLOCK3XX
# block call redirect based on 3xx replies.
if (t_check_status("3[0-9][0-9]")) {
t_reply("404","Not found");
exit;
}
#!endif
#!ifdef WITH_VOICEMAIL
# serial forking
# - route to voicemail on busy or no answer (timeout)
if (t_check_status("486|408")) {
$du = $null;
route(TOVOICEMAIL);
exit;
}
#!endif
}
-------------- next part --------------
#! /bin/sh
### BEGIN INIT INFO
# Provides: rtpproxy
# Required-Start: $remote_fs $syslog
# Required-Stop: $remote_fs $syslog
# Default-Start: 2 3 4 5
# Default-Stop: 0 1 6
# Short-Description: RTP Proxy
# Description: Relay for VoIP media streams
### END INIT INFO
PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
NAME=rtpproxy
DESC="RTP relay"
DAEMON=/usr/sbin/$NAME
USER=kamailio
GROUP=$USER
PIDFILE="/var/run/$NAME/$NAME.pid"
PIDFILE_DIR=`dirname $PIDFILE`
CONTROL_SOCK="unix:$PIDFILE_DIR/$NAME.sock"
test -x $DAEMON || exit 0
umask 002
# Include defaults if available
if [ -f /etc/default/$NAME ] ; then
. /etc/default/$NAME
fi
DAEMON_OPTS="-s $CONTROL_SOCK -u $USER:$GROUP -p $PIDFILE $EXTRA_OPTS -l 192.168.1.11 -6 /2002:c0a8:101::11 -d DBUG:LOG_LOCAL0"
if [ ! -d "$PIDFILE_DIR" ];then
mkdir "$PIDFILE_DIR"
chown $USER:$GROUP "$PIDFILE_DIR"
fi
set -e
case "$1" in
start)
echo -n "Starting $DESC: "
start-stop-daemon --start --quiet --pidfile $PIDFILE --exec $DAEMON -- $DAEMON_OPTS
echo "$NAME."
;;
stop)
echo -n "Stopping $DESC: "
start-stop-daemon --stop --quiet --oknodo --pidfile $PIDFILE --exec $DAEMON
echo "$NAME."
;;
status)
echo -n "Status $DESC: "
PID=$(cat $PIDFILE)
kill -0 $PID
rc=$?
# Check exit code
if [ "$rc" -ne 0 ]
then
echo "$NAME is NOT running."
exit 7
else
echo "$NAME is running with PID: $PID"
fi
;;
restart|force-reload)
echo -n "Restarting $DESC: "
start-stop-daemon --stop --quiet --oknodo --pidfile $PIDFILE --exec $DAEMON
sleep 1
start-stop-daemon --start --quiet --pidfile $PIDFILE --exec $DAEMON -- $DAEMON_OPTS
echo "$NAME."
;;
*)
N=/etc/init.d/$NAME
echo "Usage: $N {start|stop|status|restart|force-reload}" >&2
exit 1
;;
esac
exit 0
More information about the sr-users
mailing list