[Serusers] SER/MediaProxy Audio issues - NEED HELP

Tue Jul 25 05:48:23 CEST 2006

Hi,

What about allow and listen directives in mediaproxy.ini? I remember I
had to specify all the directives, before my mediaproxy started
functioning properly.

  Andrey.

On 7/25/06, Marc Rys <m.rys at rystec.com> wrote:
>
>
>
> Hi Ali,
>
>
>
> Yes the ATA can register with no problems.  Still one way audio.  I also
> setup a cisco 7960 phone behind NAT as well, and it's having the same one
> way audio problem.
>
>
> Thanks again.
>
> marc
>
>
> ________________________________
>
>
> From: Ali Zaidi [mailto:aligzaidi at gmail.com]
> Sent: Monday, July 24, 2006 7:50 PM
>
> To: Marc Rys
> Subject: Re: [Serusers] SER/MediaProxy Audio issues - NEED HELP
>
>
>
> To: Marc Rys
> Subject: Re: [Serusers] SER/MediaProxy Audio issues - NEED HELP
>
>
>
>
>
>
>
> Marc,
>
>
>
>
>
> you don't have to configure rtp on ATA since everything handled by
> mediaproxy. You just have to makesure that your ATA can register, using
> correct proxy server, port 5060,  credentials, everything else set to
> factory default.
>
>
>
>
>
> let meknow.
>
>
>
>
>
> Note: Set your ATA to factory default, try to register with SER using
> username, password, domain and port 5060. EVERYTHING SHOULD BE FACTORY
> DEFAULT.
>
>
>
>
>
> LET ME KNOW,
>
>
>
>
>
> ALI....
>
>
>
>
>
>
>
>
> On 7/24/06, Marc Rys <m.rys at rystec.com> wrote:
>
>
>
> I just tried all of that.. Still no luck.  I even made sure the UA's were
> using ports 10000 and higher.
>
>
>
> Any other suggestions?
>
>
> marc
>
>
>
>
>
>
>
> ________________________________
>
>
> From: Ali Zaidi [mailto: aligzaidi at gmail.com]
> Sent: Monday, July 24, 2006 4:56 PM
>
>
>
> To: Marc Rys
> Subject: Re: [Serusers] SER/MediaProxy Audio issues - NEED HELP
>
>
>
>
>
> Marc,
>
>
>
>
>
> Ok, try restarting ser + MySQL + MediaProxy then reregister your both ATA.
>
>
>
>
>
> let me know,
>
>
>
>
>
> Ali
>
>
>
>
> On 7/24/06, Marc Rys < m.rys at ivalve.net> wrote:
>
> Ali,
>
> Thank you for helping.  I've changed my mediaproxy.ini file to the
> following.  But the one way audio is still happening.
>
> Marc
>
> -----------------------------------------------------------
> Mediaproxy.ini
> -----------------------------------------------------------
>
> [Dispatcher]
> ;start = yes
> socket = /var/run/proxydispatcher.sock
> ;group = ser
> defaultProxy = /var/run/mediaproxy.sock
>
> [MediaProxy]
> start = yes
> socket = /var/run/mediaproxy.sock
> group = ser
> listen = None
> allow = None
> proxyIP = 12.178.142.235        # This is where OpenSER installed
> portRange = 10000:10100
> TOS = 0xb8
> idleTimeout = 60
> holdTimeout = 180
> forceClose = 0
> accounting = off
>
> [Accounting]
> user = root
> password =
> host = localhost
> database = ser
> table = acc
>
>
>
> ________________________________________
> From: Ali Zaidi [mailto: aligzaidi at gmail.com]
> Sent: Monday, July 24, 2006 4:40 PM
> To: Marc Rys
> Subject: Re: [Serusers] SER/MediaProxy Audio issues - NEED HELP
>
> Marc,
>
> Mediaproxy.ini has not RTP ports declare.
> ;portRange = 2000:8000 # These values are set same in ATA's configs <-
> 2000:8000 range conflict with 5060.
>
> Try following,
> portRange = 10000:10100
> then restart mediaproxy.
> Let me know if you still have problem, i can help further.
> Ali...
>
>
>
>
>
> On 7/24/06, Marc Rys < m.rys at rystec.com> wrote:
> Hello All,
>
> I'm fairly new to SER / Mediaproxy.I've been following the examples from
> onsip.org using the latest Getting started docs.
>
> At this point I'm testing with two Grandstream Handytone 486 UA' s.One
> NAT'd, one not.
>
> Please check out the following URL to see a diagram explaining my setup.
> http://marc.ivalve.net/ser/gif_1.gif
>
> "UA-2" cannot hear anything spoken from "UA-1", although I can hear what is
> said from "UA-2" on "UA-1", but not vice versa.2-way voice is not
> happening.
>
> Both UA's do register to SER.The NAT'd UA couldn't register until I got
> Mediaproxy installed.Mediaproxy does appear to start with out errors.
> Below are my Ser.cfg and Mediaproxy.ini.
>
> Please Help.
>
> Marc
>
>
>
> Ser.cfg
> --------------------------------------------------------------
> #5a-mysql-mediaproxy-ser.cfg
> debug=3
> fork=yes
> log_stderror=no
>
> listen=XXX.XXX.XXX.235 # INSERT YOUR IP ADDRESS HERE
> port=5060
> children=4
>
> dns=no
> rev_dns=no
> fifo="/tmp/ser_fifo"
> fifo_db_url="mysql://ser:heslo@localhost/ser"
>
>
> loadmodule "/usr/lib/ser/modules/mysql.so"
> loadmodule "/usr/lib/ser/modules/sl.so"
> loadmodule "/usr/lib/ser/modules/tm.so"
> loadmodule "/usr/lib/ser/modules/rr.so"
> loadmodule "/usr/lib/ser/modules/maxfwd.so"
> loadmodule "/usr/lib/ser/modules/usrloc.so"
> loadmodule "/usr/lib/ser/modules/registrar.so"
> loadmodule "/usr/lib/ser/modules/auth.so"
> loadmodule "/usr/lib/ser/modules/auth_db.so"
> loadmodule "/usr/lib/ser/modules/uri.so"
> loadmodule "/usr/lib/ser/modules/uri_db.so"
> loadmodule "/usr/lib/ser/modules/domain.so"
> loadmodule "/usr/lib/ser/modules/mediaproxy.so"
> loadmodule "/usr/lib/ser/modules/nathelper.so"
> loadmodule "/usr/lib/ser/modules/textops.so"
>
> modparam("auth_db|uri_db|usrloc", "db_url",
> "mysql://ser:heslo@localhost/ser")
> modparam("auth_db", "calculate_ha1", 1)
> modparam("auth_db", "password_column", "password")
>
> modparam("nathelper", "rtpproxy_disable", 1)
> modparam("nathelper", "natping_interval", 0)
>
> modparam("mediaproxy","natping_interval", 30)
> modparam("mediaproxy","mediaproxy_socket",
> "/var/run/mediaproxy.sock")
> modparam("mediaproxy","sip_asymmetrics","/etc/ser/sip-clients")
> modparam("mediaproxy","rtp_asymmetrics","/etc/ser/rtp-clients")
>
> modparam("usrloc", "db_mode", 2)
>
> modparam("registrar", "nat_flag", 6)
>
> modparam("rr", "enable_full_lr", 1)
>
> route {
>
> #
> ------------------------------------------------------------------------
> # Sanity Check Section
> #
> ------------------------------------------------------------------------
>
> if (!mf_process_maxfwd_header("10")) {
> sl_send_reply("483", "Too Many Hops");
> break;
> };
>
> if (msg:len > max_len) {
> sl_send_reply("513", "Message Overflow");
> break;
> };
>
> #
> ------------------------------------------------------------------------
> # Record Route Section
> #
> ------------------------------------------------------------------------
>
> if (method=="INVITE" && client_nat_test("3")) {
> # INSERT YOUR IP ADDRESS HERE
> record_route_preset("XXX.XXX.XXX.235:5060;nat=yes");
> } else if (method!="REGISTER") {
> record_route();
> };
>
> #
> -----------------------------------------------------------------
> # Call Tear Down Section
> #
> -----------------------------------------------------------------
>
> if (method=="BYE" || method=="CANCEL") {
> end_media_session();
> };
>
> #
> ------------------------------------------------------------------------
> # Loose Route Section
> #
> ------------------------------------------------------------------------
>
> if (loose_route()) {
>
> if ((method=="INVITE" || method=="REFER") && !has_totag()) {
> sl_send_reply("403", "Forbidden");
> break;
> };
>
> if (method=="INVITE") {
>
> if (!proxy_authorize("","subscriber")) {
> proxy_challenge("","0");
> break;
> } else if (!check_from()) {
> sl_send_reply("403", "Use From=ID");
> break;
> };
>
> consume_credentials();
>
> if (client_nat_test("3") || search("^Route:.*;nat=yes")) {
> setflag(6);
> use_media_proxy();
>
> };
> };
>
> route(1);
> break;
> };
>
> #
> ------------------------------------------------------------------------
> # Call Type Processing Section
> #
> ------------------------------------------------------------------------
> if (uri!=myself) {
> route(4);
> route(1);
> break;
> };
>
> if (method=="ACK") {
> route(1);
> break;
> } else if (method=="CANCEL") {
> route(3);
> break;
> } else if (method=="INVITE") {
> route(3);
> break;
> } else if (method=="REGISTER") {
> route(2);
> break;
> };
>
> lookup("aliases");
> if (uri!=myself) {
> route(4);
> route(1);
> break;
> };
>
> if (!lookup("location")) {
> sl_send_reply("404", "User Not Found");
> break;
> };
>
> route(1);
> }
>
> route[1] {
> #
> ------------------------------------------------------------------------
> # Default Message Handler
> #
> ------------------------------------------------------------------------
>
> t_on_reply("1");
>
> if (!t_relay()) {
>
> if (method=="INVITE" || method=="ACK") {
> end_media_session();
> };
>
> sl_reply_error();
> };
> }
>
> route[2] {
> #
> ------------------------------------------------------------------------
> # REGISTER Message Handler
> #
> ------------------------------------------------------------------------
>
> sl_send_reply("100", "Trying");
>
> if (!search("^Contact:[ ]*\*") && client_nat_test("7")) {
> setflag(6);
> fix_nated_register();
> force_rport();
>
> };
>
> if (!www_authorize("","subscriber")) {
> www_challenge("","0");
> break;
> };
>
> if (!check_to()) {
> sl_send_reply("401", "Unauthorized");
> break;
> };
>
> consume_credentials();
>
> if (!save("location")) {
> sl_reply_error();
> };
>
> }
>
> route[3] {
>
> #
> -----------------------------------------------------------------
> # INVITE Message Handler
> #
> -----------------------------------------------------------------
>
> if (client_nat_test("3")) {
> setflag(7);
> force_rport();
> fix_nated_contact();
> };
>
> if (!proxy_authorize("","subscriber")) {
> proxy_challenge("","0");
> break;
> } else if (!check_from()) {
> sl_send_reply("403", "Use From=ID");
> break;
> };
>
> consume_credentials();
>
> lookup("aliases");
> if (uri!=myself) {
> route(4);
> route(1);
> break;
> };
>
> if (!lookup("location")) {
> sl_send_reply("404", "User Not Found");
> break;
> };
>
> route(4);
> route(1);
> }
>
> route[4] {
>
> #-----------------------------------------------------------------
> # NAT Traversal Section
> #
> -----------------------------------------------------------------
> if (isflagset(6) || isflagset(7)) {
> if (isflagset(8)) {
> setflag(8);
> use_media_proxy();
> };
> };
> }
>
> onreply_route[1] {
>
> if ((isflagset(6) || isflagset(7)) &&
> (status=~"(180)|(183)|2[0-9][0-9]")) {
>
> if (!search("^Content-Length:[ ]*0")) {
> use_media_proxy();
> };
> };
>
> if (client_nat_test("1")) {
> fix_nated_contact();
> };
> }
>
>
> ------------------------------------------------------------
>
> mediaproxy.ini
> ------------------------------------------------------------
>
> [Dispatcher]
> ;start = yes
> socket = /var/run/proxydispatcher.sock
> ;group = ser
> defaultProxy = /var/run/mediaproxy.sock
>
> [MediaProxy]
> start = yes
> socket = /var/run/mediaproxy.sock
> group = ser
> listen = None
> allow = None
> proxyIP = XXX.XXX.XXX.235# This is where OpenSER installed
> ;portRange = 2000:8000# These values are set same in ATA's configs
> for RTP Range
> TOS = 0xb8
> idleTimeout = 60
> holdTimeout = 180
> forceClose = 0
> accounting = off
>
> [Accounting]
> user = root
> password =
> host = localhost
> database = ser
> table = acc
>
> --
> No virus found in this outgoing message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.4/396 - Release Date: 7/24/2006
>
>
> _______________________________________________
> Serusers mailing list
> Serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.4/396 - Release Date: 7/24/2006
>
> --
> No virus found in this outgoing message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.4/396 - Release Date: 7/24/2006
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.4/396 - Release Date: 7/24/2006
>
>
>
>
> --
> No virus found in this outgoing message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.4/396 - Release Date: 7/24/2006
>
>
>
> _______________________________________________
>
> Serusers mailing list
> Serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
>
>
>
>
> Serusers mailing list
> Serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
>
>
>
>
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.4/396 - Release Date: 7/24/2006
>
>
>
> --
> No virus found in this outgoing message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.10.4/396 - Release Date: 7/24/2006
>
> _______________________________________________
> Serusers mailing list
> Serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
>
>
>