[Serusers] Please help with ser/nathelper
Klaus Darilion
klaus.mailinglists at pernau.at
Tue Nov 29 10:00:57 CET 2005
How do you make sure that the main proxy sends the INVITE to the
outbound proxy, and the outbound proxy sends the request to the client?
where do you store the contact information? in the main proxy or in the
outbound proxy?
regards
klaus
Enky wrote:
> Hi,
> I am trying to run the SER as an outbound proxy. Unfortunately I have
> some problems. I have used the nathelper/rtpproxy with a customized
> ser.conf and the result is that the clients behind NAT are making
> outbound calls with no problems. The audio is two-way and all seems
> best, but when I try to react a client behind NAT I can not. It is
> registered in the SIP Proxy, but I can not dial it.
> My scenario is: SER with MySQL authorization on the first PC and SER
> with nathelper/rtpproxy for outbound proxy on second PC.
> Could someone give me some hint as I can not solve this problem. The
> Outbound Proxy SER version is:
> version: ser 0.9.3 (i386/linux)
> flags: STATS: Off, USE_IPV6, USE_TCP, DISABLE_NAGLE, USE_MCAST,
> DNS_IP_HACK, SHM_MEM, SHM_MMAP, PKG_MALLOC, FAST_LOCK-ADAPTIVE_WAIT
> ADAPTIVE_WAIT_LOOPS=1024, MAX_RECV_BUFFER_SIZE 262144, MAX_LISTEN 16,
> MAX_URI_SIZE 1024, BUF_SIZE 65535
> @(#) $Id: main.c,v 1.197 2004/12/03 19:09:31 andrei Exp $
> main.c compiled on 20:51:59 Jun 28 2005 with gcc 3.3
>
> The ser.cfg of the Outbound Proxy SER is:
> #
> # $Id: nathelper.cfg,v 1.1 2003/11/10 14:15:36 janakj Exp $
> #
> # simple quick-start config script including nathelper support
>
> # This default script includes nathelper support. To make it work
> # you will also have to install Maxim's RTP proxy. The proxy is enforced
> # if one of the parties is behind a NAT.
> #
> # If you have an endpoing in the public internet which is known to
> # support symmetric RTP (Cisco PSTN gateway or voicemail, for example),
> # then you don't have to force RTP proxy. If you don't want to enforce
> # RTP proxy for some destinations than simply use t_relay() instead of
> # route(1)
> #
> # Sections marked with !! Nathelper contain modifications for nathelper
> #
> # NOTE !! This config is EXPERIMENTAL !
> #
> # ----------- global configuration parameters ------------------------
>
> debug=3 # debug level (cmd line: -dddddddddd)
> fork=yes
> log_stderror=no # (cmd line: -E)
>
> /* Uncomment these lines to enter debugging mode
> fork=no
> log_stderror=yes
> */
>
> check_via=no # (cmd. line: -v)
> dns=no # (cmd. line: -r)
> rev_dns=no # (cmd. line: -R)
> port=5082
> children=4
> fifo="/tmp/ser_fifo"
>
> # ------------------ module loading ----------------------------------
>
> # Uncomment this if you want to use SQL database
> #loadmodule "/usr/local/lib/ser/modules/mysql.so"
>
> loadmodule "/usr/local/lib/ser/modules/sl.so"
> loadmodule "/usr/local/lib/ser/modules/tm.so"
> loadmodule "/usr/local/lib/ser/modules/rr.so"
> loadmodule "/usr/local/lib/ser/modules/maxfwd.so"
> loadmodule "/usr/local/lib/ser/modules/usrloc.so"
> loadmodule "/usr/local/lib/ser/modules/registrar.so"
> loadmodule "/usr/local/lib/ser/modules/textops.so"
>
> # Uncomment this if you want digest authentication
> # mysql.so must be loaded !
> #loadmodule "/usr/local/lib/ser/modules/auth.so"
> #loadmodule "/usr/local/lib/ser/modules/auth_db.so"
>
> # !! Nathelper
> loadmodule "/usr/local/lib/ser/modules/nathelper.so"
>
> # ----------------- setting module-specific parameters ---------------
>
> # -- usrloc params --
>
> modparam("usrloc", "db_mode", 0)
>
> # Uncomment this if you want to use SQL database
> # for persistent storage and comment the previous line
> #modparam("usrloc", "db_mode", 2)
>
> # -- auth params --
> # Uncomment if you are using auth module
> #
> #modparam("auth_db", "calculate_ha1", yes)
> #
> # If you set "calculate_ha1" parameter to yes (which true in this config),
> # uncomment also the following parameter)
> #
> #modparam("auth_db", "password_column", "password")
>
> # -- rr params --
> # add value to ;lr param to make some broken UAs happy
> modparam("rr", "enable_full_lr", 1)
>
> # !! Nathelper
> modparam("registrar", "nat_flag", 6)
> modparam("nathelper", "natping_interval", 60) # Ping interval 60 s
> modparam("nathelper", "ping_nated_only", 1) # Ping only clients behind NAT
>
> # ------------------------- request routing logic -------------------
>
> # main routing logic
>
> route{
>
> # initial sanity checks -- messages with
> # max_forwards==0, or excessively long requests
> if (!mf_process_maxfwd_header("10")) {
> sl_send_reply("483","Too Many Hops");
> break;
> };
> if (msg:len >= max_len ) {
> sl_send_reply("513", "Message too big");
> break;
> };
>
> # !! Nathelper
> # Special handling for NATed clients; first, NAT test is
> # executed: it looks for via!=received and RFC1918 addresses
> # in Contact (may fail if line-folding is used); also,
> # the received test should, if completed, should check all
> # vias for rpesence of received
> if (nat_uac_test("3")) {
> # Allow RR-ed requests, as these may indicate that
> # a NAT-enabled proxy takes care of it; unless it is
> # a REGISTER
>
> if (method == "REGISTER" || ! search("^Record-Route:")) {
> log("LOG: Someone trying to register from private IP, rewriting\n");
>
> # This will work only for user agents that support symmetric
> # communication. We tested quite many of them and majority is
> # smart enough to be symmetric. In some phones it takes a
> configuration
> # option. With Cisco 7960, it is called NAT_Enable=Yes, with
> kphone it is
> # called "symmetric media" and "symmetric signalling".
>
> fix_nated_contact(); # Rewrite contact with source IP of signalling
> if (method == "INVITE") {
> fix_nated_sdp("1"); # Add direction=active to SDP
> };
> force_rport(); # Add rport parameter to topmost Via
> setflag(6); # Mark as NATed
> };
> };
>
> # we record-route all messages -- to make sure that
> # subsequent messages will go through our proxy; that's
> # particularly good if upstream and downstream entities
> # use different transport protocol
> if (!method=="REGISTER") record_route();
>
> # subsequent messages withing a dialog should take the
> # path determined by record-routing
> if (loose_route()) {
> # mark routing logic in request
> append_hf("P-hint: rr-enforced\r\n");
> route(1);
> break;
> };
>
> if (!uri==myself) {
> # mark routing logic in request
> append_hf("P-hint: outbound\r\n");
> route(1);
> break;
> };
>
> # if the request is for other domain use UsrLoc
> # (in case, it does not work, use the following command
> # with proper names and addresses in it)
> if (uri==myself) {
>
> if (method=="REGISTER") {
>
> save("location");
> break;
> };
>
> lookup("aliases");
> if (!uri==myself) {
> append_hf("P-hint: outbound alias\r\n");
> route(1);
> break;
> };
>
> # native SIP destinations are handled using our USRLOC DB
> if (!lookup("location")) {
> sl_send_reply("404", "Not Found");
> break;
> };
> };
> append_hf("P-hint: usrloc applied\r\n");
> route(1);
> }
>
> route[1]
> {
> # !! Nathelper
> if (uri=~"[@:](192\.168\.|10\.|172\.(1[6-9]|2[0-9]|3[0-1])\.)" &&
> !search("^Route:")){
> sl_send_reply("479", "We don't forward to private IP addresses");
> break;
> };
>
> # if client or server know to be behind a NAT, enable relay
> if (isflagset(6)) {
> force_rtp_proxy();
> };
>
> # NAT processing of replies; apply to all transactions (for example,
> # re-INVITEs from public to private UA are hard to identify as
> # NATed at the moment of request processing); look at replies
> t_on_reply("1");
>
> # send it out now; use stateful forwarding as it works reliably
> # even for UDP2TCP
> if (!t_relay()) {
> sl_reply_error();
> };
> }
>
> # !! Nathelper
> onreply_route[1] {
> # NATed transaction ?
> if (isflagset(6) && status =~ "(183)|2[0-9][0-9]") {
> fix_nated_contact();
> if (!search("^Content-Length:\ 0")) {
> force_rtp_proxy();
> };
> # otherwise, is it a transaction behind a NAT and we did not
> # know at time of request processing ? (RFC1918 contacts)
> } else if (nat_uac_test("1")) {
> fix_nated_contact();
> };
> }
>
>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Serusers mailing list
> serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
More information about the sr-users
mailing list