[Serusers] Cisco3600 to SER

Wed Jun 29 09:45:04 CEST 2005

smy at addm.com wrote:
> Thanks for the tip.  Since I'm using Mediaproxy in my SER, there is
> no t_relay command in the config file.  (Again, my config is based on
> www.onsip.org doc)

? I'm sorry that I'm not capable of remembering stuff across threads, I tend 
to mix up.
However, not using t_relay  because you use mediaproxy doesn't make any 
sense to me. It's in route[1]?!

> So what I've done is placing your command at the top (1st commend) in
> the opening of route{}.

Yes, same effect... Just executed more often ;-)

> It improved the situation, since SER kept on
> resending INVITEs back to the Cisco via 5080 according to ngrep, yet
> the trying message is still sending back to the Cisco via port 5060.

Yes, that's true. The trying is auto-generated by ser.  A quick-fix would be 
to add:
sl_send_reply("100","trying...");
for all Cisco invites.  You would still get the 5060 auto-generated one, but 
at least the box will get its trying...
g-)

> I can't seem to locate (since I'm still getting familiar with SER)
> the section where it sends the trying message in the configure file. 
> Perhaps you can give me some pointers in
> where I should be placing the rewritehostport line inorder for the
> trying message to be sent on port 5080 back to the cisco.   Thanks!!
>
> The following is the Ngrep I got after the addition of the
> rewritehostport...
> U cisco-ip:54215 -> SER-ip:5080
> INVITE sip:6119203 at SER-ip;user=phone;phone-context=local SIP/2.0..Via:
> SIP/2.0/UDP  cisco-ip:5060..From: "6113640"
> <sip:6113640 at cisco-ip>..To:
> <sip:6119203 at SER-ip;user=phone;phone-context=local>.......
> U SER-ip:5080 -> cisco-ip:5060
> SIP/2.0 100 trying -- your call is important to us..Via: SIP/2.0/UDP
> cisco-ip:5060..From: "6113640" <sip:6113640 at cisco-ip>..To:
> <sip:6119203 at SER-ip;user=phone;phone-context=local>........
>
> U SER-ip:5080 -> cisco-ip:5080
>  INVITE sip:6119203 at cisco-ip:5080;user=phone;phone-context=local
> SIP/2.0..Record-Route: <sip:6119203 at SER-ip:5080;nat=yes;lr=on>..Via:
> SIP/2.0/UDP SER-ip:5080;branch=z9hG4bKea02.173ff176.0..Via:
> SIP/2.0/UDP cisco-ip:5060..From: "6113640" <sip:6113640 at cisco-ip>..To:
> <sip:6119203 at SER-ip;user=phone;phone-context=local>..............
>
>
>
>
>
> Quoting "Greger V. Teigre" <greger at teigre.com>:
>
>> Use something like this for all messages destined for the Cisco and
>> right before t_relay:
>> if(src_ip=="your_cisco_ip"){
>>  rewritehostport("your_cisco_ip:5080");
>> }
>>
>> g-)
>>
>> smy at addm.com wrote:
>>> Hi all,
>>>
>>> Thanks Greger, for pointing out the issue with the announcement port
>>> running on
>>> port 5060.  I've tried to figure this out with my engineers, but we
>>> can't find the config location of this announcement port thingy in
>>> the Cisco, let alone configuring it.
>>>
>>> As mentioned previously, the Cisco 3600 has changed it's default SIP
>>> port to 5080, but according to the ngrep report, it sends a reply
>>> (announcement) port on 5060, therefore when SER replies back to
>>> Cisco 3600, it tries to send it back via 5060 thus Cisco can not
>>> receive message.
>>> We're STUCK here!!  If there're anyone out there with experience /
>>> solution in solving this problem with the cisco, your help is needed
>>> & GREATLY appreciated!!!
>>>
>>> PS: I just need to get Cisco to work with SER!!  Any suggestions in
>>> an easier method to get this working are welcome!!
>>>
>>> Best Regards,
>>> Samuel Yeung
>>>
>>>
>>>
>>>
>>>
>>> Quoting "Greger V. Teigre" <greger at teigre.com>:
>>>
>>>> Looks like the cisco box never receives the trying...
>>>> U SER-ip:5080 -> cisco-ip:5060
>>>>
>>>> If Cisco listens to port 5080 and not 5060, it's obvious... However, 
>>>> the box announces 5060 in:
>>>> Via: SIP/2.0/UDP  cisco-ip:5060
>>>>
>>>> So, you need to change the cisco's announced port. Should be some
>>>> parameter somewhere...
>>>> g-)
>>>>
>>>> smy at addm.com wrote:
>>>>> Hi all,
>>>>>
>>>>> I'm currently working with a cisco3600 with SER 0.9.2.  Thanks to
>>>>> Onsp.org, I can land calls from SER to Cisco 3600 without any
>>>>> problems.  Yet I'm experiencing some problems with Cisco3600
>>>>> passing calls onto SER.
>>>>>
>>>>> My setup is as follow:
>>>>>
>>>>> Cisco 3600 ==> SER+Mediaproxy ===> IP Phone
>>>>>
>>>>> When a call come in via DID method through the Cisco3600, SER
>>>>> received the all SIP messages (I got it via ngrep), yet the call
>>>>> couldn't pass onto the IP Phone.
>>>>>
>>>>> Currently, all devices (including cisco) have been configured to
>>>>> use port 5080 instead of port 5060 due to port restrictions on the
>>>>> network, and that I have specified the ip in the trusted table
>>>>> under mysql.  Yet I don't know why the call still can not get
>>>>> through. The following are the logs I received from ngrep and
>>>>> cisco..... Any help is welcome and is GREATLY APPRCIATED!!
>>>>>
>>>>> ------------------- ngrep from SER server
>>>>>
>>>>> U cisco-ip:55299 -> SER-ip:5080
>>>>>  INVITE sip:6119203 at SER-ip;user=phone;phone-context=local
>>>>> SIP/2.0..Via: SIP/2.0/UDP  cisco-ip:5060..From: "6113640"
>>>>> <sip:6113640 at cisco-ip>..To:
>>>>> <sip:6119203 at SER-ip;user=phone;phone-context=local>..............
>>>>> # U SER-ip:5080 -> cisco-ip:5060
>>>>>  SIP/2.0 100 trying -- your call is important to us..Via:
>>>>> SIP/2.0/UDP 222.50.103.247:5060..From: "6113640"
>>>>> <sip:6113640 at cisco-ip>..To:
>>>>> <sip:6119203 at SER-ip;user=phone;phone-context=local>...........................
>>>>> # U cisco-ip:55299 -> SER-ip:5080
>>>>>  CANCEL sip:6119203 at SER-ip;user=phone;phone-context=local
>>>>> SIP/2.0..Via: SIP/2.0/UDP  222.50.103.247:5060..From:
>>>>> "6113640"<sip:6113640 at cisco-ip>..To:
>>>>> <sip:6119203 at SER-ip;user=phone;phone-context=local>.................
>>>>>
>>>>> ---------------- mysql trusted table
>>>>> +----------------+-------+--------------+
>>>>>> src_ip         | proto | from_pattern |
>>>>> +----------------+-------+--------------+
>>>>>> cisco-ip       | any   | ^sip:.*$     |
>>>>> +----------------+-------+--------------+
>>>>>
>>>>> ----------------- log from cisco3600
>>>>> Jun 23 14:23:53: HandleUdpSocketReads :Msg enqueued for SPI with
>>>>> IPaddr: SER-ip:5080
>>>>> Jun 23 14:23:57: Received:
>>>>> SIP/2.0 408 Request Timeout
>>>>> Via: SIP/2.0/UDP  cisco-ip:5060
>>>>> From: "6113640" <sip:6113640 at cisco3600>
>>>>> To:
>>>>> <sip:6119203 at SER-ip;user=phone;phone-context=local>;tag=bc78c497f1336138e83d95d77d963f1b-f81d
>>>>> Call-ID: 22B8BA3E-E32911D9-82A1EC22-7AD29AB0 at 222.50.103.247
>>>>> CSeq
>>>>>
>>>>> _______________________________________________
>>>>> Serusers mailing list
>>>>> serusers at lists.iptel.org
>>>>> http://lists.iptel.org/mailman/listinfo/serusers 