[Serusers] Problems making acc module with radius enabled

[Greger V. Teigre]

HEAD requires radiusclient-ng v 0.5.x, which cannot be found on your system. 
Install the newest radiusclient and you should be fine (you don't have to 
remove the old, they can co-exist)
g-)
Cameron Beattie wrote:
> I am trying to enable radius accounting.
>
> I have uncommented the following lines in the acc Makefile:
> DEFS+=-DRAD_ACC -I$(LOCALBASE)/include
> LIBS=-L$(LOCALBASE)/lib -lradiusclient
>
> I then ran the following:
> make proper include_modules="mysql"
> make
> make modules include_modules="mysql"
> make install include_modules="mysql"
>
> But I get the following message when I try to run ser, which I think
> indicates that radius accounting hasn't compiled properly:
> parameter <radius_config> not found in module <acc>
>
> I noticed the following on the make install, which doesn't look
> promising. Any ideas would be appreciated:
> make[1]: Entering directory `/usr/src/sip_router/modules/acc'
> 
> cc -fPIC -DPIC -g -O9 -funroll-loops  -Wcast-align  -Wall  -minline-all-stringops 
>  -malign-double -falign-loops -mcpu=athlon      -DNAME='"ser"'
> -DVERSION='"0.10.99-dev7"' -DARCH='"i386"' -DOS='"linux"' -DCOMPILER='"gcc
> 3.3"' -D__CPU_i386 -D__OS_linux -DCFG_DIR='"/usr/local/etc/ser/"'
> -DPKG_MALLOC -DSHM_MEM  -DSHM_MMAP -DDNS_IP_HACK -DUSE_IPV6 -DUSE_MCAST -DUSE_TCP
> -DDISABLE_NAGLE -DDBG_QM_MALLOC  -DFAST_LOCK -DADAPTIVE_WAIT
> -DADAPTIVE_WAIT_LOOPS=1024  -DHAVE_GETHOSTBYNAME2 -DHAVE_UNION_SEMUN -DHAVE_SCHED_YIELD 
>  -DHAVE_MSG_NOSIGNAL
> -DHAVE_MSGHDR_MSG_CONTROL -DHAVE_ALLOCA_H -DRAD_ACC -I/usr/local/include -c 
> acc.c -o acc.o
> acc.c:53:29: radiusclient-ng.h: No such file or directory
> acc.c:603: error: syntax error before "phrase2code"
> acc.c:604: warning: return type defaults to `int'
> acc.c: In function `phrase2code':
> acc.c:605: error: `UINT4' undeclared (first use in this function)
> acc.c:605: error: (Each undeclared identifier is reported only once
> acc.c:605: error: for each function it appears in.)
> acc.c:605: error: syntax error before "code"
> acc.c:609: error: `code' undeclared (first use in this function)
> acc.c: At top level:
> acc.c:618: error: syntax error before "rad_status"
> acc.c:619: warning: return type defaults to `int'
> acc.c: In function `acc_rad_request':
> acc.c:640: error: `VALUE_PAIR' undeclared (first use in this function)
> acc.c:641: error: `UINT4' undeclared (first use in this function)
> acc.c:641: error: syntax error before "av_type"
> acc.c:655: error: invalid lvalue in assignment
> acc.c:666: error: `av_type' undeclared (first use in this function)
> acc.c:667: warning: implicit declaration of function `rc_avpair_add'
> acc.c:764: warning: implicit declaration of function `rc_acct'
> acc.c:764: error: `OK_RC' undeclared (first use in this function)
> acc.c:768: warning: implicit declaration of function `rc_avpair_free'
> make[1]: *** [acc.o] Error 1
> make[1]: Leaving directory `/usr/src/sip_router/modules/acc'
>
> make[1]: Entering directory `/usr/src/sip_router/modules/radius_acc'
> make[1]: *** No targets specified and no makefile found.  Stop.
> make[1]: Leaving directory `/usr/src/sip_router/modules/radius_acc'
>
> Regards
>
> Cameron
>
> _______________________________________________
> Serusers mailing list
> serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers