[Serusers] SER & Mediaproxy: XLite - Audio OK, Sipura - No audio

[Cameron Beattie]

Thanks for the tips.

I have changed the NAT settings on the SPA2000 back to no NAT. I couldn't 
find the via settings you referred to so I upgraded the firmware (from 
2.0.10e to 2.0.13g) and there they were. Hmmm. Was I just blind or were they 
really not there before???

X-Lite is not configured to use stun. I've still got no audio either way 
with the settings below. The problem exists with and without stun settings:

Admin > advanced > Line 1
NAT Settings
NAT mapping enable: no
NAT keep alive enable: no

Admin > advanced > SIP
NAT Support Parameters
Handle VIA received:  yes
Handle VIA rport:   yes
Insert VIA received:  yes
Insert VIA rport:   yes
Substitute VIA Addr:  yes
Send Resp To Src Port: no
STUN Enable:  no
STUN Test Enable: no
STUN Server:
EXT IP:
EXT RTP Port Min:
NAT Keep Alive Intvl:  20

Any further pointers would be greatly appreciated.

Regards

Cameron

----- Original Message ----- 
From: "Greger V. Teigre" <greger at teigre.com>
To: "Cameron Beattie" <ext_news at appsfarm.com>; <serusers at lists.iptel.org>
Sent: Tuesday, April 19, 2005 6:44 PM
Subject: Re: [Serusers] SER & Mediaproxy: XLite - Audio OK, Sipura - No 
audio


> Cameron,
> Try turning *off* Sipura NAT mapping.  The onsip config files assume that 
> clients should not do NATing.  (However, if the clients do it properly, it 
> will work. Sipura has many various NAT options you can turn on and off)
>    Note that if you configure clients to use NAT mapping, STUN, etc, your 
> experiences with audio may be completely related to how the clients handle 
> NAT, not mediaproxy.  If the client itself detects its own public IP (or 
> you configure it manually), mediaproxy will not detect NAT and will not 
> proxy the call. I believe xlite default is configured with STUN.
>
> If you want Sipura to use STUN (and thus mediaproxy only handles symmetric 
> NATs):
> Under admin - advanced - SIP in Sipura, you will find:
> NAT Support Parameters
> Handle VIA received:  yes
> Handle VIA rport:   yes
> Insert VIA received:  yes
> Insert VIA rport:   yes
> Substitute VIA Addr:  yes
> Send Resp To Src Port: no
> STUN Enable:  yes
> STUN Test Enable: yes
> STUN Server:  your stun serve
> EXT IP:
> EXT RTP Port Min:
> NAT Keep Alive Intvl:  20
>
> These settings should work with the onsip.org config file.
>
> g-)
>
>
>
> ----- Original Message ----- 
> From: "Cameron Beattie" <kjcsb at orcon.net.nz>
> To: <serusers at lists.iptel.org>
> Sent: Tuesday, April 19, 2005 08:26 AM
> Subject: [Serusers] SER & Mediaproxy: XLite - Audio OK, Sipura - No audio
>
>
>>I am using the onsip ser.cfg for mediaproxy. All seems OK when I call 
>>between two X-Lite clients. However calls between X-Lite and a Sipura 2000 
>>have no audio in either direction. Both the X-Lite clients and the Sipura 
>>are on the same network behind NAT and going out to the SER/Mediaproxy 
>>server which has a public IP. SER and Mediaproxy are on the same server.
>>
>> I've tested SJPhone to Sipura and there's no audio also, so it seems like 
>> a Sipura issue.
>>
>> I've set NAT mapping enable and NAT Keep Alive enable to yes on the 
>> Sipura.
>>
>> What am I missing?
>>
>> Regards
>>
>> Cameron
>> _______________________________________________
>> Serusers mailing list
>> serusers at lists.iptel.org
>> http://lists.iptel.org/mailman/listinfo/serusers
>>
>>
>
> _______________________________________________
> Serusers mailing list
> serusers at lists.iptel.org
> http://lists.iptel.org/mailman/listinfo/serusers
>
>