[Serusers] AS5300/E1 + SER -> PB : Cisco redirect calls on SER

[Alcée]

Hello,
I try to use cisco AS5300 with SER, like this  :
	phones -> SER -> AS5300 -> PSTN
or
	phones -> AS5300 -> PSTN
				|
			         \/
			      SER
But the second form does not work.


I don't want people to directly ask for AS5300. So I follow the "Howto" 
on SER web page.
But nothing arrive on SER when I make a call directly to AS5300, The 
call is forward to pstn.
So I make this configuration to minimize the problem.
But nothing at all.
The "debug ccsip error" tells "no route to destination".

Have you any idea ?

thanks :)

Alcée

! Last configuration change at 14:17:05 UTC Mon Apr 11 2005 by admin
! NVRAM config last updated at 12:57:01 UTC Mon Apr 11 2005 by admin
!
version 12.3
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname VoIP
!
boot-start-marker
boot-end-marker
!
!
!
resource-pool disable
!
aaa new-model
!
!
aaa authentication login h323 group radius
aaa authorization exec h323 group radius
aaa accounting delay-start
aaa accounting connection h323 start-stop group radius
aaa nas port voip
aaa session-id common
ip subnet-zero
!
!
isdn switch-type primary-net5
!
voice rtp send-recv
voice echo-canceller extended
!
voice class codec 1
  codec preference 1 g729r8 bytes 40
  codec preference 2 g711ulaw
!
voice class codec 2
  codec preference 1 g723ar63 bytes 48
  codec preference 2 g723r63 bytes 48
  codec preference 3 g729br8 bytes 40
  codec preference 4 g729r8 bytes 40
  codec preference 5 g723ar53 bytes 40
  codec preference 6 g723r53 bytes 40
  codec preference 7 g711ulaw
!
fax interface-type modem
!
!
controller E1 0
  clock source line primary
  pri-group timeslots 1-31
!
controller E1 1
  pri-group timeslots 1-31
!
controller E1 2
  clock source line secondary 4
  pri-group timeslots 1-31
!
controller E1 3
  pri-group timeslots 1-31
gw-accounting syslog
gw-accounting aaa
  attribute h323-remote-id resolved
  acct-template callhistory-detail
  suppress pots
!
!
!
interface Ethernet0
  ip address 192.168.0.129 255.255.255.0
!
interface Serial0:15
  no ip address
  isdn switch-type primary-net5
  isdn protocol-emulate network
  no cdp enable
!
interface Serial1:15
  no ip address
  isdn switch-type primary-net5
  no cdp enable
!
interface Serial2:15
  no ip address
  isdn switch-type primary-net5
  no cdp enable
!
interface Serial3:15
  no ip address
  isdn switch-type primary-net5
  no cdp enable
!
interface FastEthernet0
  ip address 172.19.20.2 255.255.255.0
  duplex full
  speed 100
!
interface Dialer0
  no ip address
!
ip classless
ip route 0.0.0.0 0.0.0.0 172.19.20.1
no ip http server
!
!
logging facility local0
logging 192.168.0.2
!
!
radius-server host 192.168.0.2 auth-port 1812 acct-port 1813
radius-server key test
radius-server vsa send accounting
radius-server vsa send authentication
!
voice-port 0:D
!
voice-port 1:D
!
voice-port 2:D
!
voice-port 3:D
!
!
!
dial-peer voice 3777 voip
  huntstop
  preference 2
  application session
  destination-pattern 3777#T
  progress_ind setup enable 3
  progress_ind alert enable 8
  voice-class codec 2
  session protocol sipv2
session target sip-server
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
  fax rate 9600
  icpif 50
!
!
sip-ua
  retry invite 3
  retry response 3
  retry bye 3
  retry cancel 3
  timers expires 300000
  timers connect 300
  sip-server ipv4:192.168.0.1
!
!
line con 0
line aux 0
line vty 0 4
  password intermobile
!
ntp server 192.168.0.2
end