[Serusers] rtpproxy

Klaus Darilion klaus.mailinglists at pernau.at
Fri May 14 11:37:44 CEST 2004


Here is a startup script I'm using. It's just a modified startup script 
found somewhere in the ser distribution. The binary is:
SER_BIN=/usr/local/sbin/rtpproxy
Probably you have to change this to fit your needs.

Klaus

#! /bin/sh
# Copyright (c) 2002 Frauenhofer Gesellschaft FOKUS, Germany.
# All rights reserved.
#
# Author: Nils Ohlmeier <ohlmeier at fokus.fhg.de>
#
# /etc/init.d/ser
#
### BEGIN INIT INFO
# Provides:          sip
# Required-Start:    $network
# X-UnitedLinux-Should-Start: $network
# Required-Stop:     $network
# X-UnitedLinux-Should-Stop: $network
# Default-Start:     3 5
# Default-Stop:      0 1 2 6
# Short-Description: SIP Express Router
# Description:       Start SER and provide the routing of SIP requests.
### END INIT INFO


# Check for missing binaries (stale symlinks should not happen)
echo "checking for rtpproxy binary..."
SER_BIN=/usr/local/sbin/rtpproxy
test -x $SER_BIN || exit 5
echo "rtpproxy binary found"

# Shell functions sourced from /etc/rc.status:
#      rc_check         check and set local and overall rc status
#      rc_status        check and set local and overall rc status
#      rc_status -v     ditto but be verbose in local rc status
#      rc_status -v -r  ditto and clear the local rc status
#      rc_status -s     display "skipped" and exit with status 3
#      rc_status -u     display "unused" and exit with status 3
#      rc_failed        set local and overall rc status to failed
#      rc_failed <num>  set local and overall rc status to <num>
#      rc_reset         clear local rc status (overall remains)
#      rc_exit          exit appropriate to overall rc status
#      rc_active        checks whether a service is activated by symlinks
#      rc_splash arg    sets the boot splash screen to arg (if active)
. /etc/rc.status

# Reset status of this service
rc_reset

# Return values acc. to LSB for all commands but status:
# 0       - success
# 1       - generic or unspecified error
# 2       - invalid or excess argument(s)
# 3       - unimplemented feature (e.g. "reload")
# 4       - user had insufficient privileges
# 5       - program is not installed
# 6       - program is not configured
# 7       - program is not running
# 8--199  - reserved (8--99 LSB, 100--149 distrib, 150--199 appl)
#
# Note that starting an already running service, stopping
# or restarting a not-running service as well as the restart
# with force-reload (in case signaling is not supported) are
# considered a success.

case "$1" in
     start)
         echo -n "Starting rtpproxy "
         ## Start daemon with startproc(8). If this fails
         ## the return value is set appropriately by startproc.
         startproc $SER_BIN

         # Remember status and be verbose
         rc_status -v
         ;;
     stop)
         echo -n "Shutting down rtpproxy "
         ## Stop daemon with killproc(8) and if this fails
         ## killproc sets the return value according to LSB.

         killproc -TERM $SER_BIN

         # Remember status and be verbose
         rc_status -v
         ;;
     restart)
         ## Stop the service and regardless of whether it was
         ## running or not, start it again.
         $0 stop
         $0 start

         # Remember status and be quiet
         rc_status
         ;;
     force-reload)
         ## Signal the daemon to reload its config. Most daemons
         ## do this on signal 1 (SIGHUP).
         ## If it does not support it, restart.

         echo -n "Reload service SIP Express Router "
         ## Otherwise:
         $0 stop  &&  $0 start
         rc_status
         ;;
     reload)
         ## Like force-reload, but if daemon does not support
         ## signaling, do nothing (!)

         ## Otherwise if it does not support reload:
         rc_failed 3
         rc_status -v
         ;;
     status)
         echo -n "Checking for service rtpproxy "
         ## Check status with checkproc(8), if process is running
         ## checkproc will return with exit status 0.

         # Return value is slightly different for the status command:
         # 0 - service up and running
         # 1 - service dead, but /var/run/  pid  file exists
         # 2 - service dead, but /var/lock/ lock file exists
         # 3 - service not running (unused)
         # 4 - service status unknown :-(
         # 5--199 reserved (5--99 LSB, 100--149 distro, 150--199 appl.)

         # NOTE: checkproc returns LSB compliant status values.
         checkproc $SER_BIN
         # NOTE: rc_status knows that we called this init script with
         # "status" option and adapts its messages accordingly.
         rc_status -v
         ;;
     *)
         echo "Usage: $0 {start|stop|status|restart}"
         exit 1
         ;;
esac
rc_exit




More information about the sr-users mailing list