[Serusers] using voicemail

[Andrea Bondavalli]

Hi,

this is just to let you know that using the "revet_uri()" funtion I solved my problem.
Before of this I tried with:
exec_dset("echo $SIP_HF_TO | sed 's/^<//' | sed 's/>$//'; echo > /dev/null");

At this time my falilure route is:

failure_route[1] {

  t_reply("100","Trying -- going to voicemail");

 /*
 exec_dset("echo $SIP_HF_TO | sed 's/^<//' | sed 's/>$//'; echo > /dev/null");
 */

 revert_uri();

 lookup("aliases");

        if (method=="INVITE" || method=="REFER") {

                 log("**************** vm start - begin ******************\n");
                 log("****************     voicemail    ******************\n");
                 if(!vm("/tmp/am_fifo","voicemail")) {
                        log("could not contact the answer machine\n");
                        t_reply("500","could not contact the answer machine");
                 };
                 log("**************** vm start - end ******************\n");
        }
        else if (method=="BYE") {

                 log("**************** vm end - begin ******************\n");
                 log("****************   voicemail    ******************\n");
                 if(!vm("/tmp/am_fifo","bye")){
                       log("could not contact the answer machine\n");
                       t_reply("500","could not contact the answer machine");
                 };
                 log("**************** vm end - end ******************\n");
        };
}

Thank you very much,
Andrea 

----- Original Message ----- 
From: "Klaus Darilion" <klaus.mailinglists at pernau.at>
To: "Andrea Bondavalli" <a.bondavalli at inet.it>
Cc: <serusers at lists.iptel.org>
Sent: Monday, May 03, 2004 12:28 PM
Subject: Re: [Serusers] using voicemail


> you can try the revert_uri function before sending to sems. This will 
> revert the request uri to the original one (sip:bonda at sip.inet.it), so 
> that sems can find the emailaddress in the subscriber table.
> 
> klaus
> 
> Andrea Bondavalli wrote:
> > Hi,
> > 
> > the problem is that my users register more than 1 contact.
> > For example the user "sip:bonda at sip.inet.it" registers the following contacts:
> > sip:bonda at 213.92.1.100
> > sip:03472323 at sip.inet.it (to PSTN using a Cisco Gateway)
> > sip:02323232 at sip.inet.it (to PSTN using a Cisco Gateway)
> > 
> > When all of these contacts are forked by SER and all of them
> > timeout (30 seconds per INVITE) I want to
> > send the caller to the bonda's voicemail.
> > Unfortunately if the last INVITE is sent to a phone number and
> > not to 'sip:bonda at 213.92.1.100' SEMS reports:
> >  "Error: 404 voicemail: no email address for user 03472323."
> > 
> > Thank you,
> > Andrea
> > 
> > ----- Original Message ----- 
> > From: "Klaus Darilion" <klaus.mailinglists at pernau.at>
> > To: "Andrea Bondavalli" <a.bondavalli at inet.it>
> > Cc: <serusers at lists.iptel.org>
> > Sent: Friday, April 30, 2004 1:11 PM
> > Subject: Re: [Serusers] using voicemail
> > 
> > 
> > 
> >>Check if it is a gateway call before setting up the failure route.
> >>
> >>klaus
> >>
> >>if (isflagset(4)) { /*voicemail enabled*/
> >>   if (!(PSTN call?)) {
> >>       t_on_failure("1");
> >>   }
> >>}
> >>
> >>Andrea Bondavalli wrote:
> >>
> >>>Hi all,
> >>>
> >>>I am configuring SER in order to use the SEMS's voicemail
> >>>when one of my subscribed users is not avaiable or
> >>>when all the INVITEs to their contacts fail (fork).
> >>>
> >>>I'am using the following configuration:
> >>>
> >>>route {
> >>>....
> >>>if (isflagset(4)) { /*voicemail enabled*/
> >>>    t_on_failure("1");
> >>>}
> >>>
> >>>if (!t_relay()) {
> >>>    sl_reply_error();
> >>>    break;
> >>>}
> >>>
> >>>}
> >>>
> >>>failure_route[1] {
> >>>        t_reply("100","Trying -- going to voicemail");
> >>>
> >>>        if (method=="INVITE" || method=="REFER") {
> >>>                 log("**************** vm start - begin ******************\n");
> >>>                 log("****************     voicemail    ******************\n");
> >>>                 if(!vm("/tmp/am_fifo","voicemail")){
> >>>                        log("could not contact the answer machine\n");
> >>>                        t_reply("500","could not contact the answer machine");
> >>>                 };
> >>>                 log("**************** vm start - end ******************\n");
> >>>        }
> >>>        else if (method=="BYE") {
> >>>                 log("**************** vm end - begin ******************\n");
> >>>                 log("****************   voicemail    ******************\n");
> >>>                 if(!vm("/tmp/am_fifo","bye")){
> >>>                       log("could not contact the answer machine\n");
> >>>                       t_reply("500","could not contact the answer machine");
> >>>                 };
> >>>                 log("**************** vm end - end ******************\n");
> >>>        };
> >>>}
> >>>
> >>>...
> >>>
> >>>This works fine when the system calls a user's contact whose username part
> >>>matches the subscribed user name. 
> >>>Unfortunately, if the system tries to reach such a contact at a phone
> >>>number (using a gateway)  the result is that SEMS reports:
> >>>"Error: 404 voicemail: no email address for user 034823213213."
> >>>
> >>>Can you help me ?
> >>>
> >>>Best regards,
> >>>Andrea
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>_______________________________________________
> >>>Serusers mailing list
> >>>serusers at lists.iptel.org
> >>>http://lists.iptel.org/mailman/listinfo/serusers
> >>>
> >>>
> > 
> > 
> > _______________________________________________
> > Serusers mailing list
> > serusers at lists.iptel.org
> > http://lists.iptel.org/mailman/listinfo/serusers
> > 
> >