[Serusers] as5400 and ser
Stephen Kingham
Stephen.Kingham at aarnet.edu.au
Tue Jun 29 02:29:59 CEST 2004
Hello
It appears to me that the problem is in the PBX.
I took a look at ETSI standard 300 403-1 1990 Q.931 Part 1.pdf and Part
2 (get from web site) to remind myself what is supposed to happen in
ISDN Q.931.
After you Rx a Call_Proc from the PBX, the PBX should respond with
ALERTING or RELEASE (or a few other message types) unless you hangup or
a T310 timer expires.
So I would get a trace from the PABX to see what it is doing.
Here is a trace of a good call:
Jun 29 10:10:23.619 +1000: ISDN Se0:15: TX -> SETUP pd = 8 callref = 0x1F3F
Jun 29 10:10:23.619 +1000: Bearer Capability i = 0x8090A3
Jun 29 10:10:23.619 +1000: Channel ID i = 0xA98394
Jun 29 10:10:23.619 +1000: Calling Party Number i = 0x21, 0x81,
'61262223575', Plan:ISDN, Type:National
Jun 29 10:10:23.619 +1000: Called Party Number i = 0x81,
'62874225', Plan:ISDN, Type:Unknown
Jun 29 10:10:23.803 +1000: ISDN Se0:15: RX <- CALL_PROC pd = 8 callref
= 0x9F3F
Jun 29 10:10:23.803 +1000: Channel ID i = 0xA98394
Jun 29 10:10:24.403 +1000: ISDN Se0:15: RX <- ALERTING pd = 8 callref =
0x9F3F
Jun 29 10:10:24.407 +1000: Progress Ind i = 0x8488 - In-band
info or appropriate now available
Jun 29 10:10:24.407 +1000: Progress Ind i = 0x8482 - Destination
address is non-ISDN
Jun 29 10:10:26.555 +1000: %ISDN-6-CONNECT: Interface Serial0:25 is now
connected to 62554347
Jun 29 10:10:28.655 +1000: ISDN Se0:15: RX <- CONNECT pd = 8 callref =
0x9F3F
Jun 29 10:10:28.659 +1000: ISDN Se0:15: TX -> CONNECT_ACK pd = 8
callref = 0x1F3F
Jun 29 10:10:29.991 +1000: %ISDN-6-CONNECT: Interface Serial0:19 is now
connected to 62874225
Jun 29 10:10:29.995 +1000: ISDN Se0:15: TX -> DISCONNECT pd = 8 callref
= 0x1F3E
Jun 29 10:10:29.995 +1000: Cause i = 0x8090 - Normal call clearing
Jun 29 10:10:30.103 +1000: ISDN Se0:15: RX <- RELEASE pd = 8 callref =
0x9F3E
Jun 29 10:10:30.107 +1000: ISDN Se0:15: TX -> RELEASE_COMP pd = 8
callref = 0x1F3E
Jun 29 10:10:35.820 +1000: %ISDN-6-DISCONNECT: Interface Serial0:19
disconnected from 62874225 , call lasted 7 seconds
voice0.anu#
Jun 29 10:10:35.824 +1000: ISDN Se0:15: TX -> DISCONNECT pd = 8 callref
= 0x1F3F
Jun 29 10:10:35.824 +1000: Cause i = 0x8090 - Normal call clearing
Jun 29 10:10:36.104 +1000: ISDN Se0:15: RX <- RELEASE pd = 8 callref =
0x9F3F
Jun 29 10:10:36.108 +1000: ISDN Se0:15: TX -> RELEASE_COMP pd = 8
callref = 0x1F3F
CM Rahman wrote:
>Actually I have a Lucent Excel switch which is connected to the cisco
>as5400 via T1 Pri. Anybody here using Excel switch with a cisco ?
>
>Right now, when ever I do debug q931 I get this below and it hangs until
>my messenger times out and it disconnects. It should answer and give me
>voice prompt. Anybody have deal with same scenario as mine?
>
>
>
>*Feb 18 15:40:20.142: ISDN Se7/0:3:23 Q931: Applying typeplan for
>sw-type 0xD is 0x2 0x1, Called num 5122200090
>*Feb 18 15:40:20.142: ISDN Se7/0:3:23 Q931: TX -> SETUP pd = 8 callref
>= 0x005F
> Bearer Capability i = 0x8090A2
> Standard = CCITT
> Transer Capability = Speech
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Called Party Number i = 0xA1, '5122200090'
> Plan:ISDN, Type:National
>*Feb 18 15:40:20.158: ISDN Se7/0:3:23 Q931: RX <- CALL_PROC pd = 8
>callref = 0x805F
> Channel ID i = 0xA98381
> Exclusive, Channel 1
>
>&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*
>C.M. Rahman Jr.
>CTO
>CCNP, MCSE Security "Secure your self by securing your System"
>CompTI Security Plus Certified
>CCS Internet
>http://www.ccsi.com
>13704 Research Blvd. Building O-Suite 4
>Austin, TX 78750
>Tel: 512-257-2274 Ex: 115
>
>-----Original Message-----
>From: Stephen Kingham [mailto:Stephen.Kingham at aarnet.edu.au]
>Sent: Monday, June 28, 2004 5:50 AM
>To: CM Rahman
>Cc: Richard; serusers at lists.iptel.org
>Subject: Re: [Serusers] as5400 and ser
>
>
>
>CM Rahman wrote:
>
>
>
>>I am sorry, I didn't show how put the pot in my last email, here it is,
>>
>>dial-peer voice 150 voip
>>description CCSi voip phone
>>destination-pattern 9T
>>progress_ind setup enable 3
>>session protocol sipv2
>>session target ipv4:216.236.160.11
>>codec g723r53
>>
>>
>>
>>Answer to your question, without putting "isdn protocol-emulate
>>
>>
>network"
>
>
>>I wasn't able to get PRI Layer 2 up.
>>
>>
>>
>>
>Yes. ISDN has a network side and a user side so that the layer 2
>protocol Q921/lapb will work.
>
>Most PABX want to be the user side.
>
>
>
>>Any other suggestion?
>>
>>
>>
>>
>
>yes you have to have a pots dialpeer, the Cisco VoIP gateway requires at
>
>least one, I think maybe one for each E1 port.
>
>Take a look at the template I have posted here:
>http://www.aarnet.edu.au/events/conferences/2004/apan-questnet/sipworksh
>op/uas/ciscoVoIPGateways/as5300-12.3-6b-sip.txt
>
>
>
>>&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*
>>C.M. Rahman Jr.
>>CTO
>>CCNP, MCSE Security "Secure your self by securing your System"
>>CompTI Security Plus Certified
>>CCS Internet
>>http://www.ccsi.com
>>13704 Research Blvd. Building O-Suite 4
>>Austin, TX 78750
>>Tel: 512-257-2274 Ex: 115
>>
>>-----Original Message-----
>>From: Richard [mailto:mypop3mail at yahoo.com]
>>Sent: Friday, June 25, 2004 4:11 PM
>>To: CM Rahman; serusers at lists.iptel.org
>>Subject: RE: [Serusers] as5400 and ser
>>
>>Don't know why you have the following two lines,
>>isdn protocol-emulate network
>>isdn incoming-voice modem
>>
>>Also you probably need a pots dial-peer...
>>
>>Cisco web site has some configuration samples.
>>
>>--- CM Rahman <cmrahman at ccsi.com> wrote:
>>
>>
>>
>>
>>>Once I send a call via messenger, I don't hear
>>>anything other side. But
>>>after a while it disconnect.
>>>
>>>Here are the cisco config
>>>
>>>******************************
>>>controller T1 7/0:3
>>>framing esf
>>>pri-group timeslots 1-24
>>>description Prism Test
>>>
>>>***************************************
>>>interface Serial7/0:3:23
>>>no ip address
>>>isdn switch-type primary-ni
>>>isdn protocol-emulate network
>>>isdn incoming-voice modem
>>>isdn T310 180000
>>>no cdp enable
>>>!***************************************
>>>
>>>dial-peer voice 150 voip
>>>description CCSi voip phone
>>>destination-pattern 9T
>>>session protocol sipv2
>>>session target ipv4:216.236.160.11
>>>codec g723r53
>>>
>>>*****************************************
>>>
>>>
>>>
>>>
>>>*Feb 15 16:18:09.720: ISDN Se7/0:3:23 Q931: Applying
>>>typeplan for
>>>sw-type 0xD is 0x2 0x1, Called num 5122200090
>>>*Feb 15 16:18:09.720: ISDN Se7/0:3:23 Q931: TX ->
>>>SETUP pd = 8 callref
>>>= 0x002E
>>> Bearer Capability i = 0x8090A2
>>> Standard = CCITT
>>> Transer Capability = Speech
>>> Transfer Mode = Circuit
>>> Transfer Rate = 64 kbit/s
>>> Channel ID i = 0xA98381
>>> Exclusive, Channel 1
>>> Called Party Number i = 0xA1, '5122200090'
>>> Plan:ISDN, Type:National
>>>*Feb 15 16:18:09.732: ISDN Se7/0:3:23 Q931: RX <-
>>>CALL_PROC pd = 8
>>>callref = 0x802E
>>> Channel ID i = 0xA98381
>>> Exclusive, Channel 1
>>>*Feb 15 16:20:17.967: ISDN Se7/0:3:23 Q931: TX ->
>>>DISCONNECT pd = 8
>>>callref = 0x002E
>>> Cause i = 0x8290 - Normal call clearing
>>>*Feb 15 16:20:17.995: ISDN Se7/0:3:23 Q931: RX <-
>>>RELEASE pd = 8
>>>callref = 0x802E
>>>*Feb 15 16:20:17.995: ISDN Se7/0:3:23 Q931: TX ->
>>>RELEASE_COMP pd = 8
>>>callref = 0x002E
>>>
>>>
>>>
>>>
>>>
>>>
>>&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*
>>
>>
>>
>>
>>>C.M. Rahman Jr.
>>>CCNP, MCSE Security "Secure your self by securing
>>>your System"
>>>CompTI Security Plus Certified
>>>CCS Internet
>>>http://www.ccsi.com
>>>13704 Research Blvd. Building O-Suite 4
>>>Austin, TX 78750
>>>Tel: 512-257-2274 Ex: 115
>>>
>>>-----Original Message-----
>>>From: serusers-bounces at lists.iptel.org
>>>[mailto:serusers-bounces at lists.iptel.org] On
>>>Behalf Of Richard
>>>Sent: Friday, June 25, 2004 3:27 AM
>>>To: serusers at lists.iptel.org
>>>Subject: RE: [Serusers] as5400 and ser
>>>
>>>If you check this page,
>>>
>>>
>>>
>>>
>>>
>>>
>>http://www.cisco.com/en/US/tech/tk652/tk701/technologies_configuration_
>>
>>
>g
>
>
>>
>>
>>
>>
>>>uide_chapter09186a00800eadfa.html
>>>
>>>PSTN error "63 Service or option unavailable" is
>>>mapped to sip error "503 Service or option
>>>unavailable" which is in the header of the message.
>>>
>>>Also the page shows why IP phone or PSTN generates
>>>this and how proxy is supposed to do with it. Quote,
>>>"The SIP gateway generates this response if it is
>>>unable to process the request due to an overload or
>>>maintenance problem. Upon receiving this response,
>>>the
>>>gateway initiates a graceful call disconnect and
>>>clears the call. "
>>>
>>>Look like a pstn config issue. Use "debug isdn
>>>q931",
>>>"debug isdn q921" and "term mon" for further
>>>debuging.
>>>
>>>Cheers,
>>>Richard
>>>
>>>--- CM Rahman <cmrahman at ccsi.com> wrote:
>>>
>>>
>>>
>>>
>>>>Looking through your cisco config file, I am
>>>>guessing your E1 are not
>>>>Pri. Ami I correct? I am dealing with a
>>>>
>>>>
>>>>
>>>>
>>>channelized
>>>
>>>
>>>
>>>
>>>>DS3 with T1 Pri. I
>>>>will also share my config file after I can get the
>>>>call routed.
>>>>Currently I am getting this below. My
>>>>
>>>>
>>>>
>>>>
>>>understanding
>>>
>>>
>>>
>>>
>>>>is there is
>>>>something wrong in the call going from cisco to
>>>>
>>>>
>>>>
>>>>
>>>Pri
>>>
>>>
>>>
>>>
>>>>trunk. Anybody can
>>>>give me some clue, that will be great.
>>>>
>>>>
>>>>
>>>>146.82.136.218:5060 -> 216.236.160.11:5060
>>>> SIP/2.0 503 Service Unavailable..Via:
>>>>
>>>>
>>>>
>>>>
>>>SIP/2.0/UDP
>>>
>>>
>>>
>>>
>>>>216.236.160.11;branch=z9h
>>>> G4bKc513.1c338976.0,SIP/2.0/UDP
>>>>65.70.207.66:8675..From:
>>>>"pappusip at backup.c
>>>> csi.com"
>>>>
>>>>
>>>>
>>>>
>>>>
>><sip:pappusip at backup.ccsi.com>;tag=c270cb2a9ab14343b72218adb808612
>>
>>
>>
>>
>>>> 4;epid=c91b05026b..To:
>>>>
>>>>
>>>>
>>>>
>>>>
>>><sip:915125656553 at backup.ccsi.com>;tag=E8186070-487.
>>>
>>>
>>>
>>>
>>>> .Date: Tue, 15 Feb 2000 01:38:28 GMT..Call-ID:
>>>>9fef06800312431fbaa33d389f7d
>>>> 3ac7 at 192.168.1.101..Server:
>>>>Cisco-SIPGateway/IOS-12.x..CSeq: 1
>>>>INVITE..Allo
>>>> w-Events: telephone-event..Content-Length: 0....
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*&*
>>
>>
>>
>>
>>>>C.M. Rahman Jr.
>>>>CTO
>>>>CCNP, MCSE Security "Secure your self by
>>>>
>>>>
>>>>
>>>>
>>>securing
>>>
>>>
>>>
>>>
>>>>your System"
>>>>CompTI Security Plus Certified
>>>>CCS Internet
>>>>http://www.ccsi.com
>>>>13704 Research Blvd. Building O-Suite 4
>>>>Austin, TX 78750
>>>>Tel: 512-257-2274 Ex: 115
>>>>
>>>>
>>>>-----Original Message-----
>>>>From: Stephen Kingham
>>>>[mailto:Stephen.Kingham at aarnet.edu.au]
>>>>Sent: Thursday, June 24, 2004 11:56 PM
>>>>To: CM Rahman
>>>>Cc: serusers at lists.iptel.org
>>>>Subject: Re: [Serusers] as5400 and ser
>>>>
>>>>Hi
>>>>
>>>>Along with several other we are putting together a
>>>>SER implementation
>>>>Tutorial for the R&E sector.
>>>>
>>>>We have a page up the the AS5300 and it may help
>>>>you, also if anyone is
>>>>interested in reviewing it?
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>http://www.aarnet.edu.au/events/conferences/2004/apan-questnet/sipworks
>>
>>
>h
>
>
>>
>>
>>
>>
>>>>op/uas/ciscoas5300.html
>>>>
>>>>Regards
>>>>
>>>>Stephen
>>>>
>>>>CM Rahman wrote:
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>>Anybody here using cisco as5400 for PSTN
>>>>>
>>>>>
>>>>>
>>>>>
>>>>termination? I am having some
>>>>
>>>>
>>>>
>>>>
>>>>>problem with call routing. If there are such
>>>>>
>>>>>
>>>>>
>>>>>
>>>person
>>>
>>>
>>>
>>>
>>>>will to help,
>>>>please
>>>>
>>>>
>>>>
>>>>
>>=== message truncated ===
>>
>>
>>
>>
>>__________________________________
>>Do you Yahoo!?
>>Read only the mail you want - Yahoo! Mail SpamGuard.
>>http://promotions.yahoo.com/new_mail
>>
>>
>>_______________________________________________
>>Serusers mailing list
>>serusers at lists.iptel.org
>>http://lists.iptel.org/mailman/listinfo/serusers
>>
>>
>>
>>
>
>
>
--
Stephen Kingham, MIT, BSc, E&C Cert
Project Manager and Consulting Engineer
mailto:Stephen.Kingham at aarnet.edu.au
Telephone +61 2 6222 3575 (office)
+61 419 417 471 (mobile)
Voice and Video over IP
for The Australian Academic Research Network (AARNet) and
http://www.aarnet.edu.au
More information about the sr-users
mailing list