Hi,
I just notice an error in pua_reginfo and I was intrigued:
a REGISTER is received and then:
proxy[30664]: DEBUG: usrloc [udomain.c:602]: db_load_urecord(): aor 88835677220000@X.X.X.X not found in table location
proxy[30664]: DEBUG: usrloc [ul_callback.h:89]: run_ul_callbacks(): contact=0x7fddc7836b40, callback type 1/1, id 0 entered
proxy[30664]: DEBUG: pua_reginfo [usrloc_cb.c:240]: reginfo_usrloc_cb(): AOR: 88835677220000@X.X.X.X (location)
proxy[30664]: DEBUG: pua_reginfo [usrloc_cb.c:241]: reginfo_usrloc_cb(): type= UL_CONTACT_INSERT
proxy[30664]: DEBUG: usrloc [udomain.c:702]: db_load_urecord_by_ruid(): aor uloc-555da99c-77c8-1 not found in table location
proxy[30664]: ERROR: pua_reginfo [usrloc_cb.c:261]: reginfo_usrloc_cb(): '88835677220000@X.X.X.X (location)' Not found in usrloc
So I took a look over usrloc and I found that the callbacks are been
called after insert in mem but before insert on DB
when you set DB_ONLY.
int insert_ucontact(urecord_t* _r, str* _contact, ucontact_info_t* _ci, ucontact_t** _c)
{
if ( ((*_c)=mem_insert_ucontact(_r, _contact, _ci)) == 0) {
LM_ERR("failed to insert contact\n");
return -1;
}
if (exists_ulcb_type(UL_CONTACT_INSERT)) {
run_ul_callbacks( UL_CONTACT_INSERT, *_c);
}
if (db_mode == WRITE_THROUGH || db_mode==DB_ONLY) {
if (db_insert_ucontact(*_c) < 0) {
LM_ERR("failed to insert in database\n");
return -1;
} else {
(*_c)->state = CS_SYNC;
}
}
return 0;
}
This happens on update too:
int update_ucontact(struct urecord* _r, ucontact_t* _c, ucontact_info_t* _ci)
{
int res;
/* we have to update memory in any case, but database directly
* only in db_mode 1 */
if (mem_update_ucontact( _c, _ci) < 0) {
LM_ERR("failed to update memory\n");
return -1;
}
/* run callbacks for UPDATE event */
if (exists_ulcb_type(UL_CONTACT_UPDATE))
{
LM_DBG("exists callback for type= UL_CONTACT_UPDATE\n");
run_ul_callbacks( UL_CONTACT_UPDATE, _c);
}
if (_r && db_mode!=DB_ONLY)
update_contact_pos( _r, _c);
st_update_ucontact(_c);
if (db_mode == WRITE_THROUGH || db_mode==DB_ONLY) {
if (ul_db_update_as_insert)
res = db_insert_ucontact(_c);
else
res = db_update_ucontact(_c);
if (res < 0) {
LM_ERR("failed to update database\n");
return -1;
} else {
_c->state = CS_SYNC;
}
}
return 0;
}
So I would say that DB_ONLY should be honored here before calling the
callbacks
_______________________________________________
sr-dev mailing list
sr-dev@lists.sip-router.org
http://lists.sip-router.org/cgi-bin/mailman/listinfo/sr-dev